Vazo80
Newbie | Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору День добрый! Подскажите, пожалуйста, что делать с хардом? Система выдала предупреждение о повреждении второго диска на 750 ГБ в ноутбуке. Перенес все файлы на другой диск. Форматнул поврежденный. Прогнал в Victoria 4.47 Hitachi HTS547575A9E384 J2540054HTY40E ------------------------------------------------------------------------- ID Name Value Worst Tresh Raw Health ------------------------------------------------------------------------- 1 Raw read error rate 100 100 62 0 ••••• 2 Throughput perfomance 100 100 40 0 ••••• 3 Spin-up time 176 176 33 73014444033 ••••• 4 Number of spin-up times 94 94 0 9791 •••• 5 Reallocated sector count 100 100 5 0 ••••• 7 Seek error rate 100 100 67 0 ••••• 8 Seek time perfomance 100 100 40 0 ••••• 9 Power-on time 57 57 0 19084 •• 10 Spin-up retries 100 100 60 0 ••••• 12 Power cycle count 99 99 0 2619 •••• 191 G-SENSOR shock counter 97 97 0 6 •••• 192 Power-off retract count 100 100 0 174 ••••• 193 Load/unload cycle count 1 1 0 1617225 • 194 HDA Temperature 157 157 0 38°C/100°F •••• 194 Minimum temperature 90 157 0 10°C/50°F - 194 Maximum temperature 90 157 0 63°C/145°F - 196 Reallocated event count 100 100 0 0 ••••• 197 Current pending sectors 100 100 0 16 ••••• 198 Offline scan UNC sectors 100 100 0 0 ••••• 199 Ultra DMA CRC errors 200 200 0 0 ••••• 223 Load retry count 100 100 0 0 ••••• Лог после прогона теста в read-ignore и последующем read-remap: 16:10:38 : Warning! Main INI-file 'vcr40.ini' not found, and writen default sets! 16:10:39 : Starting Victoria 4.47 Freeware (2013-02-20) , 2xCPU, 1900,34 MHz, Windows unknown NT found. 16:10:39 : Select SECONDARY port: base=170h, alternative=376h 16:10:41 : Port 0170h - drive disconnected! 16:16:47 : Primary port is blocked. Please, read manual 16:16:47 : Select SECONDARY port: base=170, alternative=376h 16:16:54 : Primary port is blocked. Please, read manual 16:16:55 : Select SECONDARY port: base=170, alternative=376h 16:20:56 : Waiting of readiness... Drive not ready! 16:20:56 : [ATA protocol] DRQ!!! Press RESET or restart HDD! 16:20:56 : Get drive passport: Drive error! 16:21:10 : Waiting of readiness... Drive not ready! 16:21:10 : [ATA protocol] DRQ!!! Press RESET or restart HDD! 16:21:10 : Get drive passport: Drive error! 16:21:18 : API access enabled, device #1 16:21:34 : Get passport... OK 16:21:34 : 48bit access enabled 16:21:34 : Model: Hitachi HTS547575A9E384; Capacity: 1465149168 LBAs; SN: J2540054HTY40E; FW: JE4OA60A 16:25:41 : Get S.M.A.R.T. command... OK 16:25:43 : SMART status = GOOD 16:29:14 : Get passport... OK 16:29:16 : Recallibration... OK 16:29:17 : Starting Reading, LBA=0..1465149167, sequential access, timeout 10000ms 16:30:39 : Block 6376448 Error: ABRT 16:31:08 : Block 6384128 Error: ABRT 17:16:36 : Warning! Block start at 446325248 = 280 ms 17:16:36 : Warning! Block start at 446325760 = 281 ms 20:03:42 : ***** Scan results: Warnings - 2, errors - 2 ***** 20:11:14 : Get passport... OK 20:11:15 : Recallibration... OK 20:11:16 : Starting Reading, LBA=0..1465149167, sequential access w. REMAP, tio 1000ms 20:12:55 : LBA 6376648 try REMAR... 20:12:55 : LBA 6376648 try REMAP... Error 20:13:54 : LBA 6376649 try REMAR... 20:13:54 : LBA 6376649 try REMAP... Error 20:14:52 : LBA 6376650 try REMAR... 20:14:52 : LBA 6376650 try REMAP... Error 20:15:51 : LBA 6376651 try REMAR... 20:15:51 : LBA 6376651 try REMAP... Error 20:16:49 : LBA 6376652 try REMAR... 20:16:49 : LBA 6376652 try REMAP... Error 20:17:48 : LBA 6376653 try REMAR... 20:17:48 : LBA 6376653 try REMAP... Error 20:18:46 : LBA 6376654 try REMAR... 20:18:46 : LBA 6376654 try REMAP... Error 20:19:45 : LBA 6376655 try REMAR... 20:19:45 : LBA 6376655 try REMAP... Error 20:20:44 : LBA 6384224 try REMAR... 20:20:44 : LBA 6384224 try REMAP... Error 20:21:42 : LBA 6384225 try REMAR... 20:21:42 : LBA 6384225 try REMAP... Error 20:22:41 : LBA 6384226 try REMAR... 20:22:41 : LBA 6384226 try REMAP... Error 20:23:39 : LBA 6384227 try REMAR... 20:23:39 : LBA 6384227 try REMAP... Error 20:24:37 : LBA 6384228 try REMAR... 20:24:37 : LBA 6384228 try REMAP... Error 20:25:36 : LBA 6384229 try REMAR... 20:25:36 : LBA 6384229 try REMAP... Error 20:26:34 : LBA 6384230 try REMAR... 20:26:34 : LBA 6384230 try REMAP... Error 20:27:33 : LBA 6384231 try REMAR... 20:27:33 : LBA 6384231 try REMAP... Error 23:25:33 : ***** Scan results: Warnings - 0, errors - 16 ***** 23:45:32 : Get S.M.A.R.T. command... OK 23:45:32 : SMART status = GOOD 15:45:05 : Get S.M.A.R.T. command... OK | Всего записей: 10 | Зарегистр. 12-07-2011 | Отправлено: 14:43 06-12-2014 | Исправлено: Vazo80, 15:19 06-12-2014 |
|