VPN под Linux - [2] :: В помощь системному администратору

Это лог моих действий.
=========================

Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
10.10.11.0 * 255.255.255.0 U 0 0 0 eth0
link-local * 255.255.0.0 U 0 0 0 eth0
loopback * 255.0.0.0 U 0 0 0 lo
default 10.10.11.1 0.0.0.0 UG 0 0 0 eth0
linux:~ # ifcpnfig
bash: ifcpnfig: command not found
linux:~ # ifconfig
eth0 Link encap:Ethernet HWaddr 00:30:4F:39:71:48
inet addr:10.10.11.8 Bcast:10.10.11.255 Mask:255.255.255.0
inet6 addr: fe80::230:4fff:fe39:7148/64 Scope:Link
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1897 errors:0 dropped:0 overruns:0 frame:0
TX packets:26 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:123751 (120.8 Kb) TX bytes:2738 (2.6 Kb)
Interrupt:11 Base address:0x4000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:52 errors:0 dropped:0 overruns:0 frame:0
TX packets:52 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3360 (3.2 Kb) TX bytes:3360 (3.2 Kb)

linux:~ # pptp-command setup
1.) Manage CHAP secrets
2.) Manage PAP secrets
3.) List PPTP Tunnels
4.) Add a NEW PPTP Tunnel
5.) Delete a PPTP Tunnel
6.) Configure resolv.conf
7.) Select a default tunnel
8.) Quit
?: 1
1.) List CHAP secrets
2.) Add a New CHAP secret
3.) Delete a CHAP secret
4.) Quit
?: 2
Add a NEW CHAP secret.

NOTE: Any backslashes (\) must be doubled (\\).

Local Name:

This is the 'local' identifier for CHAP authentication.

NOTE: If the server is a Windows NT machine, the local name
should be your Windows NT username including domain.
For example:

domain\\username

Local Name: skynet3-18

Remote Name:

This is the 'remote' identifier for CHAP authentication.
In most cases, this can be left as the default. It must be
set if you have multiple CHAP secrets with the same local name
and different passwords. Just press ENTER to keep the default.

Remote Name [PPTP]:

Password:

This is the password or CHAP secret for the account specified. The
password will not be echoed.

Password:
Adding secret skynet3-18 PPTP *****

1.) List CHAP secrets
2.) Add a New CHAP secret
3.) Delete a CHAP secret
4.) Quit
?: 4
1.) Manage CHAP secrets
2.) Manage PAP secrets
3.) List PPTP Tunnels
4.) Add a NEW PPTP Tunnel
5.) Delete a PPTP Tunnel
6.) Configure resolv.conf
7.) Select a default tunnel
8.) Quit
?: 4

Add a NEW PPTP Tunnel.

1.) Other
Which configuration would you like to use?: 1
Tunnel Name: vpn
Server IP: 172.16.0.1
What route(s) would you like to add when the tunnel comes up?
This is usually a route to your internal network behind the PPTP server.
You can use TUNNEL_DEV and DEF_GW as in /etc/pptp.d/ config file
TUNNEL_DEV is replaced by the device of the tunnel interface.
DEF_GW is replaced by the existing default gateway.
The syntax to use is the same as the route(8) command.
Enter a blank line to stop.
route: add default gw 172.16.37.13
route: add -host 172.16.0.1/32 gw 10.10.11.1
route: add -host 10.10.0.0/0 gw 10.10.11.8
route:
Local Name and Remote Name should match a configured CHAP or PAP secret.
Local Name is probably your NT domain\username.
NOTE: Any backslashes (\) must be doubled (\\).

Local Name: skynet3-18
Remote Name [PPTP]:
Adding vpn - 172.16.0.1 - skynet3-18 - PPTP
Added tunnel vpn
1.) Manage CHAP secrets
2.) Manage PAP secrets
3.) List PPTP Tunnels
4.) Add a NEW PPTP Tunnel
5.) Delete a PPTP Tunnel
6.) Configure resolv.conf
7.) Select a default tunnel
8.) Quit
?: 8
linux:~ # pptp-command start vpn
Using interface ppp0
Connect: ppp0 <--> /dev/pts/2
Refusing MPPE stateful mode offered by peer
MPPE required but peer negotiation failed
Connection terminated.

================================
На вопрос роутер, правильно я вводил данные?

Server ВПН: 172.16.0.1
Мой айпи при подкл. по ВПН: 172.16.37.13

Модерирует : lynx, Crash_Master, dg, emx, ShriEkeR
Версия для печати • Подписаться • Добавить в закладки
Страницы: 1 2 3