Samsung740N
Junior Member | Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
Всем доброго времени суток.
Народ помогите с проблемой. Есть 1043ND. Был прошит прошивкой OpenWRT. Вроде все стартует, горит power, sys, мигает lan, если подключен, тоже самое wan и usb.
Вот лог загрузки:
-
U-Boot 1.1.4 (Apr 28 2011 - 15:55:09)
AP83 (ar9100) U-boot 0.0.11
DRAM:
sri
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Autobooting in 1 seconds## Booting image at bf020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Looking for OpenWrt image... found at 0xbf022000
Decompressing kernel... done!
Starting kernel at 80060000...
[ 0.000000] Linux version 3.3.8 (openwrt@msk-qdisc1.noc.yandex.net) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Mon Aug 27 19:07:23 MSK 2012
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9132 rev 2
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 28952k/32768k available (2215k kernel code, 3816k reserved, 579k data, 208k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 21 on device: ath79
[ 0.100000] MIPS: machine is TP-LINK TL-WR1043ND
[ 0.360000] bio: create slab <bio-0> at 0
[ 0.370000] Switching to clocksource MIPS
[ 0.380000] NET: Registered protocol family 2
[ 0.380000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.380000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.390000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.400000] TCP reno registered
[ 0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.410000] NET: Registered protocol family 1
[ 0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.440000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.450000] msgmni has been set to 56
[ 0.460000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.460000] io scheduler noop registered
[ 0.470000] io scheduler deadline registered (default)
[ 0.470000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.510000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.510000] console [ttyS0] enabled, bootconsole disabled
[ 0.510000] console [ttyS0] enabled, bootconsole disabled
[ 0.530000] m25p80 spi0.0: found s25sl064a, expected m25p80
[ 0.530000] m25p80 spi0.0: s25sl064a (8192 Kbytes)
[ 0.540000] 5 tp-link partitions found on MTD device spi0.0
[ 0.540000] Creating 5 MTD partitions on "spi0.0":
[ 0.550000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.560000] 0x000000020000-0x00000011ec00 : "kernel"
[ 0.560000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.570000] 0x00000011ec00-0x0000007f0000 : "rootfs"
[ 0.580000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.590000] mtd: partition "rootfs" set to be root filesystem
[ 0.600000] mtd: partition "rootfs_data" created automatically, ofs=290000, len=560000
[ 0.610000] 0x000000290000-0x0000007f0000 : "rootfs_data"
[ 0.610000] 0x0000007f0000-0x000000800000 : "art"
[ 0.620000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.630000] Realtek RTL8366RB ethernet switch driver version 0.2.3
[ 0.750000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
[ 0.750000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
[ 0.930000] rtl8366rb: probed
[ 0.940000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.240000] TCP cubic registered
[ 1.250000] NET: Registered protocol family 17
[ 1.250000] Bridge firewalling registered
[ 1.260000] 8021q: 802.1Q VLAN Support v1.8
[ 1.270000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.270000] Freeing unused kernel memory: 208k freed
[ 3.210000] eth0: link up (1000Mbps/Full duplex)
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 6.530000] JFFS2 notice: (437) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (0 unchecked, 3 orphan) and 20 of xref (0 dead, 13 orphan) found.
switching to jffs2
- init -
[ 6.720000] eth0: link down
Please press Enter to activate this console. [ 7.610000] Compat-wireless backport release: compat-wireless-2012-07-13
[ 7.620000] Backport based on wireless-testing.git master-2012-07-16
[ 7.620000] compat.git: wireless-testing.git
[ 7.650000] cfg80211: Calling CRDA to update world regulatory domain
[ 7.660000] cfg80211: World regulatory domain updated:
[ 7.660000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 7.670000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 7.680000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 7.690000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 7.690000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 7.700000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.030000] usbcore: registered new interface driver usbfs
[ 8.030000] usbcore: registered new interface driver hub
[ 8.040000] usbcore: registered new device driver usb
[ 8.510000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
[ 8.520000] cfg80211: Calling CRDA for country: US
[ 8.530000] cfg80211: Regulatory domain changed to country: US
[ 8.530000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.540000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 8.550000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 8.560000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.560000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.570000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.580000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 8.630000] PPP generic driver version 2.4.2
[ 8.780000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.880000] NET: Registered protocol family 24
[ 8.900000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.910000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[ 8.910000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 8.950000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 8.970000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 8.970000] hub 1-0:1.0: USB hub found
[ 8.980000] hub 1-0:1.0: 1 port detected
[ 9.000000] nf_conntrack version 0.5.0 (455 buckets, 1820 max)
[ 9.210000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 12.520000] eth0: link up (1000Mbps/Full duplex)
[ 12.520000] device eth0.1 entered promiscuous mode
[ 12.530000] device eth0 entered promiscuous mode
[ 12.530000] br-lan: port 1(eth0.1) entered forwarding state
[ 12.540000] br-lan: port 1(eth0.1) entered forwarding state
[ 14.540000] br-lan: port 1(eth0.1) entered forwarding state
Что я только с ним не делал. На tpl не реагирует. Внутрь не пускает. Резет не проходит.
Если выставить в компе адрес сетевухи 192.168.1.5, а шлюз поставить 192.168.1.1 показывает экран логина, НО ввожу логин root пароль, пишет пароль неверный. Заманался уже. Может у кого то есть какие то мысли? Перечитал весь форум. Перепробовал описанные способы. Толку - Ноль.
Добавлено:
Прикупил кабель usb-rs232, внутри было две микрушки. Одну выбрал оставил PL2303. Putty заработал, до этого кракозябры были. но все равно ничего не могу сделать. |
