saifullin
Newbie | Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
Здравствуйте, уважаемые братья по шаманству.
[/
Купил сей девайс с целью приспособить винт как переносной)). БП попался с соплёй и Винт гакрылся медным тазом. Ну и Х да с ним.
Перепрошил с 1й до 7й версии Потом до 14й. После этого он пиликал светодиодом. Тулбокс его не видел. Припаял переходник для прошивки Флэхи, затем решил что без уарта не обойтись. В начале ноль эмоций. Чему я не удивился. Работая своим незачищенным паяльником разворотил межслойные переходы. Но после нескольких попыток (может и 1 из самопальных переходников не работал) на терминале вышла инфа:
U-Boot 1.1.4 (May 23 2008 - 15:31:39)
U-Boot code: 00000000 -> 0001AF60 BSS: -> 0001FED4
IRQ Stack: 00e6ff7c
FIQ Stack: 00e6ef7c
RAM Configuration:
Bank #0: 00000000 32 MB
Flash Manufacturer: ST
Flash: 8 MB
In: serial
Out: serial
Err: serial
PLL clock at 250MHz
CPU clock at 250MHz
AHB clock at 125MHz
APB clock at 62MHz
## Starting application at 0x01000000 ...
Uncompressing Linux.............................................................
........................................................ done, boo
l.
Linux version 2.6.16-star (rain@ubuntu-nas) (gcc version 3.3.6) #125 Wed Jun 9 1
0:06:23 CST 2010
CPU: FA526id(wb) [66015261] revision 1 (ARMv4)
Machine: STAR STR8131
Warning: bad configuration page, trying to continue
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 8192 bytes, associativity 2, 16 byte lines, 256 sets
CPU0: D cache: 8192 bytes, associativity 2, 16 byte lines, 256 sets
PLL clock at 250MHz
CPU clock at 250MHz
AHB clock at 125MHz
APB clock at 62MHz
Built 1 zonelists
Kernel command line: root=/dev/mtdblock3
PID hash table entries: 256 (order: 8, 4096 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB = 32MB total
Memory: 28648KB available (2984K code, 670K data, 92K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
GPIOA_DATA_INPUT_REG is:10fdff0!!!!!!!!!!!!!
USB disconnect to PC now
NET: Registered protocol family 16
PCI clock at 33M
PCI: bus0: Fast back to back transfers disabled
PCI Bridge found
PCI map irq: 00:00.00 slot 0, pin 1, irq: 0
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NetWinder Floating Point Emulator V0.97 (extended precision)
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
NTFS driver 2.1.26 [Flags: R/O].
SGI XFS with no debug enabled
Initializing Cryptographic API
io scheduler noop registered (default)
str8131_rtc.o: rtc module version 1.0.0
str8131_wdt.o: watchdog module version 1.0.1
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x78000000 (irq = 9) is a 16550A
serial8250: ttyS1 at MMIO 0x78800000 (irq = 10) is a 16550A
usbmon: debugfs is not available
str8131-ehci str8131-ehci: str8131-ehci
str8131-ehci str8131-ehci: new USB bus registered, assigned bus number 1
str8131-ehci str8131-ehci: irq 24, io mem 0xcc000000
str8131-ehci str8131-ehci: USB 0.0 start
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (STR8131)
str8131-ohci str8131-ohci: str8131-ohci
str8131-ohci str8131-ohci: new USB bus registered, assigned bus number 2
str8131-ohci str8131-ohci: irq 23, io mem 0xc4000000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
loop: loaded (max 8 devices)
Star NIC Driver(for Linux Kernel 2.6) - Star Semiconductor
rxring.vir_addr=0xFFC0A000 rxring.phy_addr=0x01C15000
txring.vir_addr=0xFFC0B000 txring.phy_addr=0x01D3A000
Star Internal PHY
MAC Addr: 00:aa:bb:cc:dd:ee
star_nic_init_module: internal phy patch included.
star_nic_init_module: scatter/
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
STR8131 IDE: Register IDE success
STR8131 IDE: Register IDE DMA success
STR8131 SPI: init
m25p80 spi1.0: m25p64 (8192 Kbytes)
Creating 6 MTD partitions on "m25p80":
0x00000000-0x00020000 : "BootLoad
0x00020000-0x00040000 : "Enviroment"
0x00040000-0x00220000 : "Kernel"
0x00220000-0x007f0000 : "RootFS"
0x007f0000-0x00800000 : "Config"
0x00040000-0x007f0000 : "Kernel & RootFS"
i2c /dev entries driver
str8131_int28vbus_inthandler_init:
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
NET: Registered protocol family 5
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
==> 00c00000
VFS: Mounted root (squashfs filesystem) readonly.
Freeing init memory: 92K
Mon Jul 28 12:00:00 UTC 2008
cp: /etc/.[^.]*: No such file or directory
mv: unable to rename `/tmp/.[^.]*': No such file or directory
eth0:star_nic_lan_open
star_nic_enable: starting patch check.
Set LAN port MAC to 00:0b:2b:c0:74:81
MAC Addr: 00:0b:2b:c0:74:81
info, udhcpc (v0.9.9-pre) started
====> Starting System Services ... <====
1. Load GPIO module [ OK ]
2. Load buttond [ OK ]
3. Load system config file [ OK ]
4. Load automountd [ OK ]
5. Get server name [ OK ]
5. Get server name [ OK ]
7. Sync group name [ OK ]
8. Reload http passwd [ OK ]
9. Reset network [ OK ]
10. Load net tool server [ OK ]
11. System time setting [ OK ]
12. Time zone setting [ OK ]
13. Reset http server [ OK ]
==> DEBUG main.c | main 133 | Vsftpd support code convert!
14. Run ftp server [ OK ]
15. Synchronize time from network [ OK ]
16. Load printerd [ OK ]
17. Load upnp av [ OK ]
18. Start samba(smbd/nmbd) [ OK ]
====> All serverices starting over! <====
Sysinit done!
BusyBox v1.1.2 (2009.12.01-03:13+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
/ $ ==> DEBUG buttond.c | main 470 | buttond wakened!
[/
Возникло неск. вопросов:
-Может ли девайс самостоятельно набирать логин\пароль для подключения к инету (PPPOE (miniWAN)) ?
-Всё ли хорошо ,если судить по логу? |
Всего записей: 5 | Зарегистр. 26-10-2007 | Отправлено: 13:55 06-11-2010 | Исправлено: saifullin, 13:59 06-11-2010 |
|
