Перейти из форума на сайт.

НовостиФайловые архивы
ПоискАктивные темыТоп лист
ПравилаКто в on-line?
Вход Забыли пароль? Первый раз на этом сайте? Регистрация
Компьютерный форум Ru.Board » Операционные системы » Другие ОС » VxWorks

Модерирует : lynx, dg

 Версия для печати • ПодписатьсяДобавить в закладки

Открыть новую тему     Написать ответ в эту тему

XcomX1

Newbie
Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
Добрый день!
Помогите решить проблему!
 
Промышленное оборудование, управляется с помощью панельного компьютера. Программа для этого компьютера записана на Compact flash. Программа создана в среде VxWorks. Я хотел скопировать программу с Compact Flash на ПК, при копировании произошла ошибка, теперь на Compact Flash некоторые папки не открываются, появляется ошибка "файл или папка поврежден". Я восстановил эти файлы с помощью Recover программы (R-studio). Но программа на панельном ПК не запускается. После загрузки Bios, зависает черный экран. Также я попытался восстановить загрузочный сектор Compact flash, нашел инструкцию в интернете как восстановить boottable для VxWorks, теперь при загрузке выдает такую ошибку:  
  V 1.6+++++++++++++++
  ++++++++++++++++++
  +++++++++++++++++++  
 
Спасибо!
С уважением, Игорь!

Всего записей: 1 | Зарегистр. 27-02-2014 | Отправлено: 19:42 27-02-2014
TheYman

Newbie
Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
Привет ...
вот это почитай  
Continuously reboots or just stops
If HyperTerminal shows the board booting and then shows:
 
VxLd 1.2 ……………………………………………………………………
………………………………………………………………………………
 
 
And it either stops or reboots then the problem is that the file bootrom.sys can not be found on the CF. This can occur for two reasons:
 
•    The disk geometry in the BIOS is set up incorrectly, see section IDE Channel 0 Master – 2Gb Compact FLASH
 
•    The file is not contiguous on the CF, to check this remove the CF from the RTM ad insert into a CF reader connected to an XP computer (a CF USB reader plugged into client 1 is fine) and in a cmd window run the command:
 
chkdsk f:\bootrom.sys  
 
where f: is the CF drive, change as required. This command will report the status of the bootrom.sys file as either contiguous or split into several parts. If it is split into several parts copy to the desktop, delete all files from the CF and then copy bootrom.sys back to the CF. Re-run chkdsk.
 
Load error, complains it can’t find a file or just hangs
•    Check that VxWorks-332 is in the VxWorks folder in AppExes.
•    Check that the correct Ethernet cable is plugged in, this is a favorite to get wrong, note that Eth0 on the RTM is next to the USB port and should be connected to the main Ethernet switch (the one with most of the cables)
Missing RJ45 : RS232 connector/converter

Всего записей: 2 | Зарегистр. 05-02-2010 | Отправлено: 20:04 24-07-2014
Открыть новую тему     Написать ответ в эту тему

Компьютерный форум Ru.Board » Операционные системы » Другие ОС » VxWorks


Реклама на форуме Ru.Board.

Powered by Ikonboard "v2.1.7b" © 2000 Ikonboard.com
Modified by Ru.B0ard
© Ru.B0ard 2000-2024

BitCoin: 1NGG1chHtUvrtEqjeerQCKDMUi6S6CG4iC

Рейтинг.ru