Smyg1
Gold Member | Редактировать | Профиль | Сообщение | ICQ | Цитировать | Сообщить модератору
http://files.hddguru.com/download/Non-PC-3000%20firmwares/Western%20Digital/Sadle%20G6/5400.6%207200.11%2012.rar
Repair method of LBA = 0:
Executive Ctrl + Z will appear the following prompt:
F3 T>
Then enter:
F3 T> m0,2,2,0,0,0,0,22 Enter to;
Finished off the hard power repaired;
Three: the hard drive is not ready, the drive status indicator in the "busy" state
First, the drive circuit board removed, the connection instruction and data lines, execute the following command after power:
Ctrl + Z
F3 T>
LED: 000000CC FAddr: 0025BF67
your drive is bussy!
F3 T> / 2
F3 2>
F3 2> Z
Spin Down Complete
Elapsed Time 0.138 msecs
F3 2>
Do not power off the circuit board is mounted to the plate body, enter the following command:
F3 2> U
Returns Information: Spin Up Complete
Elapsed Time 7.242 secs
F3 2>
F3 T> / 1
F3 1> N1
Return information: this is a S.M.A.R.T. erase
Turn off hard disks, and then turn the power;
Executive: CTRL + Z
F3 T> i4,1,22
Information: this is G-list erase
Turn off hard disks, and then turn the power;
CTRL + Z on terminal
F3 T> m0,2,2,0,0,0,0,22 Enter
Not happy (497,179,758) 23:30:46
After the test erases hard to fill all the sector data is 0, the data unrecoverable.
F: / T> M0,0,8,0,0,0,0,22 Enter. Two hours later. See the starting sector no data. Power, hanging from the disk, then
SATA 2 ports, has no bad sectors. Bad road repair is completed.
qwert (875527142) 23:31:30
This has been a behind what NOT forget
Not happy (497,179,758) 23:31:50
Some ES.2 and 7200.11 LED panel displays in command mode: 00000000CC errors, hard disk status display has been busy, can not identify the parameters
. For disk repair method ES.2 and 7200.11 of this disc there are some differences.
1. The first disc and a terminal connection method specification connected, and load management in selected series 7200.11
2. Enter the command mode, power-off, and then keep pressing CTRL + Z will "F3 T>" is displayed
3. Then you need tweezers two points short circuit, if successful, will show "INVAILD COMMAND INPUT", otherwise,
Display "LED: 00000000CC", and then enter the following command will not work, repeat steps 2 and 3 to the success.
4. If the third step is successful, then back at 2 mode, enter the command Z, after completion, and then enter the U instruction, returned to normal completion 1
Mode input level N1. If the power can be completed normally. After power-on, hard disk can be ready.
5. Then repair capacity can be completed.
F3 T> m0,6,2 ,,,,, 22
Defect Reconstruction
F3 T> m0,8,2,1,1 ,,, 22
Low-level formatting, simple SF
The quality of the detection head
T> 7
7> X
No HOST FIS-ReadyStatusFlags 2002A1A5
ASCII Diag mode
F3 T> / 2
F3 2> Z
Spin Down Complete
Elapsed Time 6.015 secs
F3 2>
ASCII Diag mode
F3 T> / 2
F3 2> U
HighPowerMode
ExecuteSpinRequest
Spin Up Complete
Elapsed Time 3.624 secs
F3 2> / 1
F3 1> N1
Init SMART Fail
LED: 000000CC FAddr: 0024E4A3
LED: 000000CC FAddr: 0024E4A3
LED: 000000CC FAddr: 0024E4A3
LED: 000000CC FAddr: 0024E4A3
Characterization of the phenomenon is not detected, try to reset SMART error, suggesting as follows:
F3 1> N1
Init SMART Fail
LED: 000000CC FAddr: 0024E4A3
LED: 000000CC FAddr: 0024E4A3
LED: 000000CC FAddr: 0024E4A3
LED: 000000CC FAddr: 0024E4A3
Resolution process: F3 T> / 2
F3 2> Z
F3 2> U
F3 2> /
F3 T> m0,2,2 ,,,,, 22
F3 T> / 1
F3 1> N1
This time it can clear SMART, and if not, then m0,2,2 ,,,, 22 clear, however.
The previous steps in the repair is busy, but do not break the link and the motor plate, can be directly input command (if disconnect occurs No
HOST FIS-ReadyStatusFlags 2002A1A5 following a string of wrong).
After clearing SMART still is too busy show, this time do not ignore it, direct power, power-OK.
|
