michfood
Newbie | Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору v0.431a Drive: 0(ATA) Model: ADATA SP900 Fw : 5.0.6c Size : 61057 MB --- SandForce specific --- Signature : 158-0-28199 Controller : SF-2000 HW Revision : 400026BB (B02CuPd) Try to unlock the drive (default)... Drive unlocked (default)! FW : [CV5ABBF0 ] FW string : [B:FW_PPRO_DALECREST:FW_PPRO_C_V_5_Release-545010 ] Config file : [cfg/cfg_MLC_Intel_64Gb_JS29F16B08CCMF3_1Q_2C_1D_S ] ROM Revision: [300 ] NAND ID : 0x89, 0x88, 0x24, 0x4b, 0xa9, 0x84, 0x0, 0x0 Page Size : 8936 NAND CE : 2 Sector/Page : 8 Die/CE : 1 Block/Die : 2048 Page/Block : 256 Raw Size : 134217728 NAND Max EC : 3000 Max PE Cycles : need fw.360+/520+ Cur PE Cycles : need fw.360+/520+ Life In Seconds : 0 (Not Set) LBA Size : 125045424 Sector Size : 512 Sector Align : +0 NAND ID : 0x89,0x88 Serial Output Control : Default(Off) Erase R Block : Disable Panic Handling Enabled : Disable Panic On SATA Error : Disable Write Throttling Test Mode: Disable R.A.I.S.E. : Disable Flash CE : 8 Bank00: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die Bank01: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die Bank02: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die Bank03: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die Bank04: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die Bank05: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die Bank06: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die Bank07: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die UART freq : 0 SATA Status Coalescing : 0 Compressible data performance tuning option : 0 (no tuning for compr. data) Serial Output Control : 0 (Default) Write Speed Limit : 0 (Off) Led Settings Activity LED Polarity : 0 (Normal) Fault LED Polarity : 0 (Normal) LED Blink Rate : 0 (250ms) Power Managment Settings Power Management Version : 2 (B01) Active State Power Mode : 0 (Default) DIPM Behavior in Active State : 0 (Default) HIPM Behavior in Active State : 2 (HIPM NAK) Auto Idle Enable : 0 (Default) Idle State Power Mode : 0 (Default) DIPM Behavior in Idle State : 0 (Default) HIPM Behavior in Idle State : 2 (HIPM NAK) Standby State Power Mode : 0 (Default) DIPM Behavior in Standby State : 0 (Default) HIPM Behavior in Standby State : 2 (HIPM NAK) Sleep State Power Mode : 0 (Default) DIPM Behavior in Sleep State : 0 (Default) HIPM Behavior in Sleep State : 2 (HIPM NAK) Auto slumber timer : 0 CMU power down : 0 (Default) Dual-align BIST Feature : 0 (Default) Temperature Sensor Settings Sensor 1: Device ID : 2 (LM73) Device Address : 0 Max Temperature Threshold Level 1 Entry Point (MT1) : 0n (Default - 65C) Max Temperature Threshold Level 2 Entry Point (MT2) : 0n (Default - 70C) Min Temperature Threshold (LT1) : 0n (Default - 0C) Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default) Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default) Min Temperature Threshold Behavior (LT1B) : 0 (Default) Max Temperature Threshold Level 1 Return Point (MTR1): 0 (Default - MT1) Sensor 2: Device ID : 255 (Disabled) Device Address : 0 Max Temperature Threshold Level 1 Entry Point (MT1) : 0 Max Temperature Threshold Level 2 Entry Point (MT2) : 0 Min Temperature Threshold (LT1) : 0 Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default) Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default) Min Temperature Threshold Behavior (LT1B) : 0 (Default) Max Temperature Threshold Level 1 Return Point (MTR1): 0 Security Erase Options Security Erase Behavior : 0 (Default) Enhanced Security Erase Behavior (Military Erase) : 0 (Default) SATA Command and Firmware Options Flush Cache Behavior : 0 (Default) ATA Security Set Enable : 0 (Default) Spread Spectrum Clocking Enable : 0 (Default) SATA Link Handling on Reboot : 0 (Default) ACS2 Support : 0 (Default) Failed Secure Unlock Delay Enable : 0 (Default(No delay)) Seek Complete in Error Status : 0 (Default) Read Long with Retry and without Retry : 0 (Default) Read Sectors without Retry : 0 (Default) Write DMA without Retry : 0 (Default) Write Long with Retry and without Retry : 0 (Default) Max SATA Link Rate : 0 (Default) Deterministic Trim Setting : 0 (Default) Controller Drive Strength Rate : 0 (Default) PHY Setting : 0 (Default) Controller Slew Rate : 0 (Default) Put SIG FIS Delay : 0 (Default) Set Multiple Handling : 0 (Default) TRIM Timer Abort : 0 (Enable(Default)) Trim Support/Setting Word 169 Bit 0 : 0 (Default(Firmware default setting)) RDD1 Optimization : 0 (Default) Security Unlock Drive : 0 (Default(Compare Master Password)) Power Throttling Options Average Power Level 0-100 : 0 Maximum Power Level 0-100 : 0 Power Throttling Upon Unsafe Shutdown : 0 (Default) Dynamic Read Scrub Read Scrub Enabled : 0 (Default (Enabled)) Dynamic Read Scrub End Range1 : 0 Dynamic Read Scrub Rate Range1 : 0 Dynamic Read Scrub End Range2 : 0 Dynamic Read Scrub Rate Range2 : 0 Dynamic Read Scrub End Range3 : 0 Dynamic Read Scrub Rate Range3 : 0 Dynamic Read Scrub End Range4 : 0 Dynamic Read Scrub Rate Range4 : 0 Low Level Format Settings Number of entries in Max LBA Setting : 1 Sub-Sector Size [0] : 512 Pattern Size [0] : 2 Sub-Sector and Patterns per sector [0] : 0 Max LBA Count [0] : 125045424 Host Protected Area Host Protected Access : 0 (Always Reset HPA State On COMRESET) End of Life Behavior Enable End of Life : 0 (Default (EOL Enabled)) EOL Threshold 1 Type : 0 (Default (SSD Life Left)) EOL Threshold 1 Percentage : 0 EOL Threshold 1 Behavior : 0 (Default (Light Write Throttling)) EOL Threshold 2 Type : 0 (Default (SSD Life Left)) EOL Threshold 1 Percentage : 0 EOL Threshold 1 Behavior : 0 (Default (Heavy Write Throttling)) CDU Smart settings: default Fab Defect list entry : 11 Idx Bus CE Die Plane Block Lane3210 Defects 0 0 0 0 0 45 BBBB 4 1 0 0 0 1 45 BBBB 4 2 0 1 0 0 45 BBBB 4 3 0 1 0 1 45 BBBB 4 4 0 1 0 0 56 ___B 1 5 0 1 0 0 79 _B__ 1 6 0 1 0 0 128 _B__ 1 7 0 1 0 0 344 ___B 1 8 0 0 0 0 348 ___B 1 9 0 1 0 0 1405 B___ 1 10 0 1 0 0 2027 ___B 1 Fab Defects : 23 User Defect list entry: 0 Panic Dumps : 0 Panic Dumps list: Idx Accurev SyncCode UnlockLevel Size DataSize EPA Log Ok CRC Ok 0 -1 0xffffffff 0xffffffff -1 -1 0x00040002 0x0000 0x0000 1 -1 0xffffffff 0xffffffff -1 -1 0x00040082 0x0000 0x0000 2 -1 0xffffffff 0xffffffff -1 -1 0x00050002 0x0000 0x0000 3 -1 0xffffffff 0xffffffff -1 -1 0x00050082 0x0000 0x0000 MST settings not exist. MST result not exits. | Всего записей: 3 | Зарегистр. 22-11-2019 | Отправлено: 13:25 01-12-2019 | Исправлено: michfood, 13:29 01-12-2019 |
|