deep222
Junior Member | Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
v0.431a
Drive: 2(USB)
Model: INTEL SSDSC2BF240A5H REF
Fw : LWDi
Size : 228936 MB
--- SandForce specific ---
Signature : 180-0-29563
Controller : SF-2000
HW Revision : 400026BB (B02CuPd)
FW : [LUD]
FW string : [B:FW_PPRO_TS_P2_L_U_C_20150109_999841:FW_PPRO_TS_P2_L_U_D_Release-1040772 ]
Config file : [cfg/cfg_MLC_Hynix_RDD_64Gb_H27QDG8UDE5R_2Q_4C_1D_S ]
ROM Revision: [300 ]
NAND ID : 0xad, 0xde, 0x14, 0xa7, 0x42, 0x4a, 0x0, 0x0
Page Size : 18048
NAND CE : 4
Sector/Page : 8
Die/CE : 1
Block/Die : 1024
Page/Block : 256
Raw Size : 536870912
NAND Max EC : 2000
Max PE Cycles : need fw.360+/520+
Cur PE Cycles : need fw.360+/520+
Life In Seconds : 0 (Not Set)
LBA Size : 468862128
Sector Size : 512
Sector Align : +0
NAND ID : 0xad,0xde
Serial Output Control : Default(Off)
Erase R Block : Disable
Panic Handling Enabled : Disable
Panic On SATA Error : Disable
Write Throttling Test Mode: Disable
R.A.I.S.E. : Enable
Flash CE : 32
Bank00: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank01: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank02: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank03: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank04: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank05: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank06: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank07: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank08: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank09: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank10: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank11: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank12: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank13: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank14: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank15: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank16: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank17: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank18: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank19: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank20: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank21: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank22: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank23: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank24: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank25: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank26: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank27: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank28: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank29: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank30: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
Bank31: 0xad,0xde,0x14,0xa7,0x42,0x4a,0xad,0xde - Hynix 16nm MLC 16k 64Gb/CE 64Gb/die
UART freq : 0
SATA Status Coalescing : 0
Compressible data performance tuning option : 0 (no tuning for compr. data)
Serial Output Control : 0 (Default)
Write Speed Limit : 0 (Off)
Led Settings
Activity LED Polarity : 1 (Inverted)
Fault LED Polarity : 0 (Normal)
LED Blink Rate : 0 (250ms)
Power Managment Settings
Power Management Version : 1 (B02)
PS1 Support : 2 (No)
HIPM Support : 1 (NACK/Off)
DIPM Support : 2 (Supported)
Auto-Partial to Slumber Timer for Active PS0 State : 0 (Default (10 ms))
Auto-Partial to Slumber Timer PS States other than PS0 : 0 (Default (0 ms))
HIPM Auto-Partial Slumber Behavior : 0 (Default)
w76b9 Supports Partial and Slumber IPM States (HIPM) : 1 (Not Supported)
w76b13 Supports Host Automatic Partial to Slumber Transitions (HIPM) : 1 (Not Supported)
w76b14 Supports Device Automatic Partial to Slumber Transitions (DIPM): 1 (Not Supported)
w78b3 Supports Device Initiating Interface Power Management Request : 0 (Default)
Auto Quick Idle Timer : 0 (Default (50ms))
DIPM Slumber COMWAKE : 2 (Enabled)
w79b7 Supports Device APS Software Settings Preservation (SSP) : 0 (Default)
w78b10 Supports DIPM Software Settings Preservation (SSP) : 1 (Not Supported)
Auto PS1 : 8
DevSleep Settings
DevSleep Support : 2 (Supported)
DevSleep Wakeup with COMWAKE : 0 (Default)
Temperature Sensor Settings
Sensor 1:
Device ID : 1 (LM75 or TMP102)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 70n
Max Temperature Threshold Level 2 Entry Point (MT2) : 75n
Min Temperature Threshold (LT1) : 0n (Default - 0C)
Max Temperature Threshold Behavior for MT1 (MT1B) : 8 (Temperature Threshold Event Log, PLL/2)
Max Temperature Threshold Behavior for MT2 (MT2B) : 11 (Temperature Threshold Event Log, PLL/4 and Heavy Write Speed SATA Throttling)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 68
Sensor 2:
Device ID : 255 (Disabled)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0
Max Temperature Threshold Level 2 Entry Point (MT2) : 0
Min Temperature Threshold (LT1) : 0
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0
Security Erase Options
Security Erase Behavior : 2 (Expanded)
Enhanced Security Erase Behavior (Military Erase) : 11 Crypto erase only)
SATA Command and Firmware Options
Flush Cache Behavior : 1 (Enable Checkpoint)
ATA Security Set Enable : 1 (Off)
Spread Spectrum Clocking Enable : 2 (On)
SATA Link Handling on Reboot : 0 (Default)
ACS2 Support : 2 (Enabled)
Failed Secure Unlock Delay Enable : 0 (Default(No delay))
Seek Complete in Error Status : 2 (Reset seek complete in error status (0x41 will be sent on cmd abort))
Read Long with Retry and without Retry : 0 (Default)
Read Sectors without Retry : 0 (Default)
Write DMA without Retry : 2 (Disabled)
Write Long with Retry and without Retry : 0 (Default)
Max SATA Link Rate : 0 (Default)
Deterministic Trim Setting : 0 (Default)
Controller Drive Strength Rate : 0 (Default)
PHY Setting : 0 (Default)
Controller Slew Rate : 2 (Low)
Put SIG FIS Delay : 0 (Default)
Set Multiple Handling : 2 (Complete)
TRIM Timer Abort : 1 (Disable)
Trim Support/Setting Word 169 Bit 0 : 1 (Disable)
RDD1 Optimization : 0 (Default)
Security Unlock Drive : 0 (Default(Compare Master Password))
Power Throttling Options
Average Power Level 0-100 : 0
Maximum Power Level 0-100 : 0
Power Throttling Upon Unsafe Shutdown : 0 (Default)
Dynamic Read Scrub
Read Scrub Enabled : 0 (Default (Enabled))
Dynamic Read Scrub End Range1 : 0
Dynamic Read Scrub Rate Range1 : 0
Dynamic Read Scrub End Range2 : 0
Dynamic Read Scrub Rate Range2 : 0
Dynamic Read Scrub End Range3 : 0
Dynamic Read Scrub Rate Range3 : 0
Dynamic Read Scrub End Range4 : 0
Dynamic Read Scrub Rate Range4 : 0
Low Level Format Settings
Number of entries in Max LBA Setting : 1
Sub-Sector Size [0] : 512
Pattern Size [0] : 2
Sub-Sector and Patterns per sector [0] : 0
Max LBA Count [0] : 468862128
Host Protected Area
Host Protected Access : 0 (Always Reset HPA State On COMRESET)
End of Life Behavior
Enable End of Life : 0 (Default (EOL Enabled))
EOL Threshold 1 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Light Write Throttling))
EOL Threshold 2 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Heavy Write Throttling))
CDU Smart settings: defined 28 attributes
## Attr IntId Tresh Flag
00 0x01 0x01 2 0x2f
01 0x05 0x28 0 0x32
02 0x09 0x04 0 0x32
03 0x0c 0x05 0 0x32
04 0xaa 0x2d 10 0x33
05 0xab 0x2e 0 0x32
06 0xac 0x2f 0 0x32
07 0xad 0x40 5 0x33
08 0xae 0x0b 0 0x32
09 0xb7 0x38 0 0x32
10 0xb8 0x0e 90 0x33
11 0xbb 0x0f 0 0x32
12 0xbc 0x10 0 0x32
13 0xbe 0x12 0 0x32
14 0xc0 0x0b 0 0x32
15 0xc2 0x12 0 0x32
16 0xc4 0x28 0 0x32
17 0xc6 0x3d 0 0x32
18 0xc7 0x37 0 0x32
19 0xe1 0x2a 0 0x32
20 0xe2 0x30 0 0x32
21 0xe3 0x31 0 0x32
22 0xe4 0x32 0 0x32
23 0xe8 0x2d 10 0x33
24 0xe9 0x54 0 0x32
25 0xf1 0x2a 0 0x32
26 0xf2 0x2b 0 0x32
27 0xf9 0x1b 0 0x32
Fab Defect list entry : 43
Idx Bus CE Die Plane Block Lane3210 Defects
0 1 0 0 1 1024 __B_ 1
1 0 1 0 0 1047 __B_ 1
2 0 1 0 1 1050 __B_ 1
3 0 0 0 0 1055 __B_ 1
4 0 2 0 0 5 _B_B 2
5 0 0 0 0 244 __B_ 1
6 0 3 0 1 312 _B__ 1
7 1 3 0 0 407 B___ 1
8 0 0 0 0 424 __B_ 1
9 1 3 0 0 493 ___B 1
10 0 3 0 0 624 __B_ 1
11 0 2 0 0 647 ___B 1
12 1 0 0 1 663 __B_ 1
13 0 1 0 0 667 __B_ 1
14 0 3 0 0 699 __B_ 1
15 1 3 0 0 703 B___ 1
16 1 3 0 0 710 ___B 1
17 0 1 0 0 734 ___B 1
18 1 0 0 1 749 __B_ 1
19 1 0 0 1 751 __B_ 1
20 1 0 0 0 756 ___B 1
21 0 0 0 0 800 __B_ 1
22 1 0 0 1 820 __B_ 1
23 0 3 0 0 820 ___B 1
24 1 3 0 0 866 B___ 1
25 0 3 0 0 872 __B_ 1
26 0 1 0 0 874 ___B 1
27 0 1 0 0 886 __B_ 1
28 1 0 0 0 927 ___B 1
29 0 0 0 0 936 __B_ 1
30 0 1 0 1 967 __B_ 1
31 0 3 0 0 969 __B_ 1
32 1 0 0 0 980 _B__ 1
33 1 3 0 0 1005 __B_ 1
34 1 3 0 0 1008 __B_ 1
35 1 1 0 1 1015 _B__ 1
36 1 0 0 0 1017 ___B 1
37 0 1 0 1 1017 __B_ 1
38 0 1 0 1 1019 __B_ 1
39 1 1 0 1 1019 _B__ 1
40 0 3 0 1 1022 ___B 1
41 1 0 0 0 1023 ___B 1
42 1 1 0 1 1023 _B__ 1
Fab Defects : 44
User Defect list entry: 0
Panic Dumps : 0
Panic Dumps list:
Idx Accurev SyncCode UnlockLevel Size DataSize EPA Log Ok CRC Ok
0 1040772 0x0ff9676e 0xffffff00 3388 2956768 0x00040002 0x0001 0x0000
1 -1 0xffffffff 0xffffffff -1 -1 0x20040002 0x0000 0x0000
2 -1 0xffffffff 0xffffffff -1 -1 0x00040102 0x0000 0x0000
3 -1 0xffffffff 0xffffffff -1 -1 0x20040102 0x0000 0x0000
MST settings not exist.
MST result:
Format Version : 4
Test State : Not Activated
Input Offset : 80
Current Command : Write
Cycles Required : 5
Cycles Complete : 5
ElapsedTime : 9200
StartTemperature : 76
MaxTemperature : 87
Grown Bad Block : 0
Errors:
Program : 0
Correctable RAISE : 0
Uncorrectable RAISE: 0
Erase : 0
Unintended Erase : 0
Upper Page Program : 0
Lower Page Program : 0
0_Bit : 1468398521 53.97%
1_Bit : 884093813 32.50%
2_Bit : 286766755 10.54%
3_Bit : 66596020 2.45%
4_Bit : 12468890 0.46%
5_Bit : 2013431 0.07%
6_Bit : 293685 0.01%
7_Bit : 40273
8_Bit : 5391
9_Bit : 728
10_Bit : 84
11_Bit : 12
12_Bit : 1
|
