Перейти из форума на сайт.

НовостиФайловые архивы
ПоискАктивные темыТоп лист
ПравилаКто в on-line?
Вход Забыли пароль? Первый раз на этом сайте? Регистрация
Компьютерный форум Ru.Board » Hardware » Магнитные носители информации » Ремонт SSD накопителей на контроллерах SandForce (часть 3)

Модерирует : Akam1, Dr_StandBy, Dekker

 Версия для печати • ПодписатьсяДобавить в закладки
Страницы: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

Открыть новую тему     Написать ответ в эту тему

Akam1



Комса
Редактировать | Профиль | Сообщение | ICQ | Цитировать | Сообщить модератору

Цитата:
exwein
   Это уже откровенный бред. Каждые 2-3 страницы вплывает новый новичек с одной и той же фразой "Все прочитал, ничего нет" Не умеете пользоваться информацией, отдайте тем кто умеет.
Что еще не понятного?
Механизм до ужаса прост:
-определить конфиг
-сделать лицензию
-запустить федору
-распаковать
-прошить
-profit

 
Подробнее...

Хотите отремонтировать SSD на базе Sandforce? Читайте шапку ниже. Там есть всё, вопросы пишем в тему.

Вопрос: почитал немного шапку, в принципе, всё понятно. а как нужный конфиг распаковать? мне, например, 27770 нужен, а там в файле lic его нет  
Ответ: В шапке читаем пункт: Про файлы lic


64Gb
в строке описания конфигурации не равно 64GB, а равно 8GB. это плотность одного кристалла флеша (не корпуса - в корпусе их бывает несколько), и тем более не всего диска. не надо на это обращать внимание при подборе номера конфигурации.
Hачало восстановления SSD
Программа определения конфигурации SSD (чипов памяти) от wlo
Data кабель от мобильного как преобразователь USB to UART.
Про файлы lic
SF-2000_Flash_Support_List.xlsx


  • Генерация прошивки в виртуалке на vmware workstation 14
  • Восстановление SSD дисков на контроллере SandForce SF-2XXX (Видео инструкция)
  • Восстановление SSD дисков на контроллере SandForce SF-2XXX
  • Практика восстановления SSD OCZ Vertex 3 на чипе Sandforce SF-2281
  • Опыт восстановления SSD OCZ Vertex 2 60Gb (OCZSSD2-2VTXE60G)
  • Восстановление SSD дисков на контроллере SandForce SF-1222
     
    Обход ошибки Format Drive Failed with extStatus c048, PanicCode=0
    Ошибка Типа: FATAL_ERROR (0x10090020:SF_GENESIS_ALREADY_RUNNING_MFB_ERROR)
    Ошибка Типа:  Proceeding in non-ROM mode, Download feature 3...
    Ошибка Типа: Could not get the IDENTIFY data from the drive...
    Ошибка: FATAL_ERROR: Could not get the IDENTIFY data from the drive...  
    (0x00100001:SF_SATA_DEVICE_NOT_PRESENT_ERROR)

    Вход в Rom mode


    FW PPRO
    Апдейтилки
    SSD NAND Data Base
    Data Sheet
     
    Быстрый поиск в теме по CTRL+F доступен здесь
    Поиск софта по SSD самостоятельно
    что есть #
    Eсли на форуме не нашли, то вам сюда

    Коротко об Phison

    Часть 1 - Часть 2

  • Всего записей: 26125 | Зарегистр. 20-04-2006 | Отправлено: 04:31 29-01-2018 | Исправлено: SRUTSSSSSSSS80, 20:36 20-11-2018
    Alekslyas

    Newbie
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    Инициализировал, Акронисом. А вот на этапе форматирования выскакивает ошибка "проверьте диск"

    Всего записей: 28 | Зарегистр. 31-05-2006 | Отправлено: 21:40 08-02-2018
    SRUTSSSSSSSS80



    Silver Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору

    Цитата:
    p.s.Нужно пункты шапки пронумеровать....  

    А смысл? Alekslyas всё равно не читает, пока его не ткнут

    Всего записей: 3116 | Зарегистр. 23-04-2006 | Отправлено: 22:26 08-02-2018
    Alekslyas

    Newbie
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    SRUTSSSSSSSS80, уважаемый, проходи мимо моих постов.
     
    Добавлено:
    Все получилось благодаря exwein и wlo . Ребята, Вам респект! А+++++

    Всего записей: 28 | Зарегистр. 31-05-2006 | Отправлено: 00:55 09-02-2018
    tower7

    Junior Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    Alekslyas


    Цитата:
     
    Все получилось

    Как удалось отформатировать ? Такой ситуации здесь ещё не было, какие сведения в шапку добавлять ?

    Всего записей: 55 | Зарегистр. 25-07-2016 | Отправлено: 08:23 09-02-2018 | Исправлено: tower7, 08:24 09-02-2018
    exwein

    Full Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    tower7, давно есть http://forum.ru-board.com/topic.cgi?forum=84&topic=5360&start=0&limit=1&m=6#1
    Но шапку читать, не всем религия позволяет.

    Всего записей: 433 | Зарегистр. 29-03-2016 | Отправлено: 09:27 09-02-2018
    tower7

    Junior Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    exwein
    Я про другое, там после этого было:

    Цитата:
    Инициализировал, Акронисом. А вот на этапе форматирования выскакивает ошибка "проверьте диск"

    А потом:  

    Цитата:
    Все получилось благодаря exwein и wlo . Ребята, Вам респект! А+++++

    Нет расшифровки, что произошло между этими двумя событиями.

    Всего записей: 55 | Зарегистр. 25-07-2016 | Отправлено: 09:42 09-02-2018 | Исправлено: tower7, 09:53 09-02-2018
    justalex1

    Junior Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    Уважаемый всеми wlo , приветствую !
    Вынужден был на долго отложить развлечения со своим гемороем М2 ВизионТек 500Гиг , здоровье подкачало . Я таки разобрался и с САТА и с еСли . Вот лог УАРТпопытки залить конфигу 33045. Пока не могу понять проблемы , мож подскажете чё ?
    С Ув.  
     
    ecli api log msg :  
     
    ecli - version 0000.0000.11.0 Built at: Jun  6 201112:28:28
    [02-09-18 15:03:34.676] ecli - version 0000.0000.11.0 Built at: Jun  6 201112:28:28
    [02-09-18 15:03:34.676] eCLI_SerialInit:103 String section 0x00000000 size 0
    [02-09-18 15:03:34.676]
    << Send Wake up, Wait 250 ms >>
    [02-09-18 15:03:35.194] << Send Wake up, Wait 250 ms >>
    [02-09-18 15:03:35.194]<< Awake >>
    [02-09-18 15:03:35.455]Failed: UART Time Out, status = 0x1  
    [02-09-18 15:03:37.479] Failed to load string, reload
    [02-09-18 15:03:37.479]Failed: UART Time Out, status = 0x1  
    [02-09-18 15:03:39.498] Failed to load string, reload
    [02-09-18 15:03:39.498]Failed: UART Time Out, status = 0x1  
    [02-09-18 15:03:41.513] Retried 3 times. Failed to load string sections! Please check drive and UART cable!
    [02-09-18 15:03:41.513]TOUT: Switch to ASCII state
    [02-09-18 15:03:44.454] [ROM] PORRST
    [[02-09-18 15:03:44.454] [ROM] Rev: 402  CID: 200026BB  BID: 625280
    [ROM] Try BCH[1]: CP=33 EC=54 EP=485
    [[02-09-18 15:03:44.478] [ROM] Try BCH[2]: CP=29 E=48 EP=485
    [[02-09-18 15:03:44.488] [ROM] Try BCH[3]: CP=36 EC=59 EP=485
    [[02-09-18 15:03:44.488] [ROM] Try BCH[4]: CP=39 EC=64 EP=485
    [ROM] Load CRP
    [[02-09-18 15:03:44.508] [CRP] Switching to Sync...
    [ROM] Load FWR
    [[02-09-18 15:03:44.518] [ROM] Failed to find/load Flashware from Root, rror=255
    [[02-09-18 15:03:44.528] [ROM] Force Download: waiting for Download Microcode ommand...
    [[02-09-18 15:03:44.538] [ROM] Waiting for Link to come up...
    OM] Link is UP.
    [ROM] Hard Reset ===> Link is Down.
    [[02-09-18 15:03:54.566] [ROM] PHY Ready
    [[02-09-18 15:03:54.566] [ROM] Sig Sent
    [ROM] Undec Cmd 0xec
    [[02-09-18 15:03:54.871] [ROM] Undec Cmd 0xef
    [[02-09-18 15:03:54.871] [ROM] Undec Cmd 0xef
    [[02-09-18 15:03:54.881] [ROM] Undec Cmd 0xec
    [[02-09-18 15:03:54.881] [ROM] Undec Cmd 0x0
    [[02-09-18 15:03:54.881] [ROM] Undec Cmd 0xef
    [ROM] Undec Cmd 0xe0
    [ROM] Hard Reset ===> Link is Down.
    [[02-09-18 15:04:18.735] [ROM] PHY Ready
    [[02-09-18 15:04:18.735] [ROM] Sig Sent
    [ROM] Undec Cmd 0xec
    [[02-09-18 15:04:19.040] [ROM] Undec Cmd 0xef
    [[02-09-18 15:04:19.040] [ROM] Undec Cmd 0xef
    [[02-09-18 15:04:19.050] [ROM] Undec Cmd 0xec
    [[02-09-18 15:04:19.050] [ROM] Undec Cmd 0x0
    [[02-09-18 15:04:19.050] [ROM] Undec Cmd 0xef
    [ROM] Data Cmd
    [[02-09-18 15:04:19.071] [ROM] READ NCQ CMD
    [[02-09-18 15:04:19.071] [ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000000
    [[02-09-18 15:04:19.081] [ROM] Data Cmd
    [[02-09-18 15:04:19.081] [ROM] READ NCQ CMD
    [[02-09-18 15:04:19.091] [ROM] R_NCQ done, lba:00000008, count:00000008, tag:00000000
    [[02-09-18 15:04:19.101] [ROM] Undec Cmd 0xec
    [ROM] Data Cmd
    [[02-09-18 15:04:19.111] [ROM] READ NCQ CMD
    [[02-09-18 15:04:19.111] [ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000000
    [[02-09-18 15:04:19.121] [ROM] Data Cmd
    [[02-09-18 15:04:19.121] [ROM] READ NCQ CMD
    [[02-09-18 15:04:19.131] [ROM] R_NCQ done, lba:00000018, count:00000008, tag:00000000
    [[02-09-18 15:04:19.141] [ROM] Data Cmd
    [[02-09-18 15:04:19.141] [ROM] READ NCQ CMD
    [[02-09-18 15:04:19.141] [ROM] R_NCQ done, lba:00000010, count:00000008, tag:00000000
    [[02-09-18 15:04:19.151] [ROM] Data Cmd
    [[02-09-18 15:04:19.151] [ROM] READ NCQ CMD
    [[02-09-18 15:04:19.161] [ROM] R_NCQ done, lba:00000020, count:00000008, tag:00000000
    [[02-09-18 15:04:19.171] [ROM] Data Cmd
    [[02-09-18 15:04:19.171] [ROM] READ NCQ CMD
    [[02-09-18 15:04:19.171] [ROM] R_NCQ done, lba:00000008, count:00000008, tag:00000000
    M] READ NCQ CMD
    [[02-09-18 15:04:19.191] [ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000000
    [[02-09-18 15:04:19.201] [ROM] Undec Cmd 0xec
     15:04:19.211] [ROM] READ NCQ CMD
    [[02-09-18 15:04:19.211] [ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000000
    [[02-09-18 15:04:19.221] [ROM] Data Cmd
    [[02-09-18 15:04:19.221] [ROM] READ NCQ CMD
    [[02-09-18 15:04:19.231] [ROM] R_NCQ done, lba:00000010, count:00000008, tag:00000000
    [[02-09-18 15:04:19.241] [ROM] Data Cmd
    [[02-09-18 15:04:19.241] [ROM] READ NCQ CMD
    [[02-09-18 15:04:19.241] [ROM] R_NCQ done, lba:00000018, count:00000008, tag:00000000
    [[02-09-18 15:04:19.251] [ROM] Data Cmd
    [[02-09-18 15:04:19.251] [ROM] READ NCQ CMD
    [[02-09-18 15:04:19.261] [ROM] R_NCQ done, lba:00000020, count:00000008, tag:00000000
    [[02-09-18 15:04:19.271] [ROM] Data Cmd
    [[02-09-18 15:04:19.271] [ROM] READ NCQ CMD
    [[02-09-18 15:04:19.271] [ROM] R_NCQ done, lba:00000008, count:00000008, tag:00000000
    [ROM] Undec Cmd 0xec
    [ROM] Undec Cmd 0xb0
    [ROM] Undec Cmd 0x92
    [[02-09-18 15:04:42.240] [ROM] non-DMA
    [ROM] Undec Cmd 0x92
    [[02-09-18 15:04:42.338] [ROM] non-DMA
    [ROM] Undec Cmd 0x92
    [[02-09-18 15:04:42.430] [ROM] non-DMA
    [ROM] Undec Cmd 0x92
    [[02-09-18 15:04:42.521] [ROM] non-DMA
    [ROM] Undec Cmd 0x92
    [[02-09-18 15:04:42.613] [ROM] non-DMA
    <MFB> FlashQuadCtrlVerifyFlash: Lane 0 CE 0 Bus 0
    <[02-09-18 15:04:42.667] <MFB> FlashQadCtrlVerifyFlash: Lane 0 CE 0 Bus 1
    <[02-09-18 15:04:42.677] <MFB> FlashQuadCtrlVerifylash: Lane 0 CE 1 Bus 0
    <[02-09-18 15:04:42.687] <MFB> FlashQuadCtrlVerifyFlash: Lane 0 CE 1 Bus 1
    <[02-09-18 15:04:42.697] <MFB> FlashQuadCtrlVerifyFlash: Lane 1 CE 0 Bus 0
    <[02-09-18 15:04:42.697] <MFB> FlashQuadCtrlVerifyFlash: Lane 1 CE 0 Bus 1
    <[02-09-18 15:04:42.707] <MFB> FlashQuadCtrlVerifyFlash: Lane 1 CE 1 Bus 0
    <[02-09-18 15:04:42.717] <MFB> FlashQuadCtrlVerifyFlash: Lane 1 CE 1 Bus 1
    <[02-09-18 15:04:42.727] <MFB> FlashQuadCtrlVerifyFlash: Lane 2 CE 0 Bus 0
    <[02-09-18 15:04:42.737] <MFB> FlashQuadCtrlVerifyFlash: Lane 2 CE 0 Bus 1
    <[02-09-18 15:04:42.737] <MFB> FlashQuadCtrlVerifyFlash: Lane 2 CE 1 Bus 0
    <[02-09-18 15:04:42.747] <MFB> FlashQuadCtrlVerifyFlash: Lane 2 CE 1 Bus 1
    <[02-09-18 15:04:42.757] <MFB> FlashQuadCtrlVerifyFlash: Lane 3 CE 0 Bus 0
    <[02-09-18 15:04:42.767] <MFB> FlashQuadCtrlVerifyFlash: Lane 3 CE 0 Bus 1
    <[02-09-18 15:04:42.777] <MFB> FlashQuadCtrlVerifyFlash: Lane 3 CE 1 Bus 0
    <[02-09-18 15:04:42.777] <MFB> FlashQuadCtrlVerifyFlash: Lane 3 CE 1 Bus 1
    <[02-09-18 15:04:42.787] <MFB> ********************************
    <[02-09-18 15:04:42.797] <MFB> ***** Basic FLASH tests OK *****
    -09-18 15:04:42.807] <MFB> ---> Sector size 0 bytes L-Page size 8192 bytes <---
    S[02-09-18 15:04:42.817] Security: Disabled  
    H[02-09-18 15:04:42.817] H/w Decode enabled
    <[02-09-18 15:04:42.827] <MFB>  
     
     
    *[02-09-18 15:04:42.827] *** MFB 582 Jul  3 2014 04:06:48 B:FW_PPRO_5_6_1_20140326_836378:FW_PPRO_5_8_2_Release-906190
    *[02-09-18 15:04:42.837] *** Build Options : cfg/cfg_MLC_MIC_128Gb_MT29F1TG08CUCAB_2Q_2C_2D -noenterprise -lp8k -asic -subdir SF-2281_Board -pdump -elog -ecli -relese -ecliLevel0 -div2 -sysclk300 -nochipsocket -mfb -noecli -sufix PP_R02264_s512 ANYHOST
    *[02-09-18 15:04:42.877] *** Chip RevId from HW: B03 (ID=62520), FW Targeted For: B02 ASIC ***
    *[02-09-18 15:04:42.887] *** SysClk : 300 MHz
    *[02-09-18 15:04:42.887] *** Packer : 500 MHz
    *[02-09-18 15:04:42.897] *** Flash  : 830 MHz
    *[02-09-18 15:04:42.897] *** FlaDiv : 2
    *[02-09-18 15:04:42.897] *** GP1011 : 2 (0=Async ONFI, 1=Toggle, 2=ONFI, 3=Async Toggle)
    <[02-09-18 15:04:42.907] <MFB>  
    *[02-09-18 15:04:42.907] *** GPIO0 : 1
    <[02-09-18 15:04:42.917] <MFB> Scap charge wait
    <[02-09-18 15:04:42.917] <MFB> Scap charge done
    <[02-09-18 15:04:42.917] <MFB User> libSfStartC enter cfg:3fff4d48
    <[02-09-18 15:04:42.927] <MFB> RootFileOpen(): not allowed yet [fid:8, mode:00000001, flags:00000003].
    <[02-09-18 15:04:42.937] <MFB User> UserMain: CheckRetiredBlkCntAtClearSmart failed.
    <MFB> PIO Flash Rblock Test on 0 - bus:2 ce:2 die:2 lane:4 pagent:1 correctPwr:304 seed:dead1a66 markers:4000
     Errors in BUS:0 CE: 0 DIE:0 [  LANE 1: 0002, <MFB> ]
     Errors in BUS:1 CE: 0 DIE:0 [  LANE 0: 0003,  LANE 1: 0002,  LNE 3: 0003, <MFB> ]
     Errors in BUS:0 CE: 1 DIE:0 [  LANE 0: 0003,  LANE 1: 0003,  LNE 2: 0003,  LANE 3: 0003, <MFB> ]
     Errors in BUS:1 CE: 1 DIE:0 [  LANE 0: 0003,  LANE 2: 0003, <MB> ]
     Errors in BUS:0 CE: 0 DIE:1 [  LANE 0: 0003,  LANE 2: 0042,  LNE 3: 0002, <MFB> ]
     Errors in BUS:1 CE: 0 DIE:1 [  LANE 0: 0003,  LANE 1: 0003, <MFB> ]
     Errors in BUS:0 CE: 1 DIE:1 [  LANE 1: 0003,  LANE 2: 0003,  LNE 3: 0003, <MFB> ]
     Errors in BUS:1 CE: 1 DIE:1 [  LANE 0: 0002,  LANE 2: 0003, <MFB> ]
    <MFB> Special Bad Block Scan: Valid 0 NumBytes 959 numOnes 1
    <[02-09-18 15:04:54.906] <FB> Read Device ID: 2C A4 E5 3C A5 00
    <[02-09-18 15:04:54.916] <MFB> == Format mode ONEalign 0 ==
    <[02-09-18 15:04:54.926] <MFB> ---> Sector size 0 bytes L-Page size 8192 byts <---
    <[02-09-18 15:04:54.936] <MFB> Flash ID Check
    <[02-09-18 15:04:54.936] <MFB> Creating New Root
    <[02-09-18 15:04:54.936] <MFB> Bad Block Discovery ...
    <MFB> Number of Bad Blocks for SE/plane/lane
    <[02-09-18 15:04:55.363] <MFB>  SE pl: ln0ln1 ln2 ln3
    <[02-09-18 15:04:55.373] <MFB>   0  0:   1   1   1   1  
    <[02-09-18 15:04:55.373] <MFB>   0  1:   1   1   1   1  
    <[02-09-18 15:04:55.383] <MFB>   1  0:   1   1   1   1  
    <[02-09-18 15:04:55.383] <MFB>   1  1:   1   1   1   1  
    <[02-09-18 15:04:55.393] <MFB>   2  0:   1   1   1   1  
    <[02-09-18 15:04:55.393] <MFB>   2  1:   1   1   1   1  
    <[02-09-18 15:04:55.403] <MFB>   3  0:   1   1   1   1  
    <[02-09-18 15:04:55.403] <MFB>   3  1:   1   1   1   1  
    <[02-09-18 15:04:55.413] <MFB>   4  0:   2   1   1   1  
    <[02-09-18 15:04:55.413] <MFB>   4  1:   1   6   1   1  
    <[02-09-18 15:04:55.423] <MFB>   5  0:   1   1   1   1  
    <[02-09-18 15:04:55.423] <MFB>   5  1:   1   1   1   1  
    <[02-09-18 15:04:55.433] <MFB>   6  0:   1   1   1   1  
    <[02-09-18 15:04:55.433] <MFB>   6  1:   1   1   1   1  
    <[02-09-18 15:04:55.443] <MFB>   7  0:   1   1   1   1  
    <[02-09-18 15:04:55.443] <MFB>   7  1:   1   1   1   1  
    <[02-09-18 15:04:55.453] <MFB> Total Bad Block number is: 70 out of 65536
    <[02-09-18 15:04:55.453] <MFB> Added donor[0]= 45
    <[02-09-18 15:04:55.463] <MFB> Added donor[1]= 396
    <[02-09-18 15:04:55.463] <MFB> Added donor[2]= 400
    <[02-09-18 15:04:55.473] <MFB> Added donor[3]= 428
    <[02-09-18 15:04:55.473] <MFB> Added donor[4]= 486
    <[02-09-18 15:04:55.483] <MFB> Added donor[5]= 786
    <[02-09-18 15:04:55.483] <MFB> Enabling Remap Unit...
    <[02-09-18 15:04:55.483] <MFB> Erasing All Virgin Blocks...
    <MFB> No Host GDL!
    <[02-09-18 15:05:06.154] <MFB> Creating the Root Record ...
    154] <MFB> Input PE:     0
    <[02-09-18 15:05:06.206] <MFB> Drive RDD:100000 RDD Low:100000, PE:  3000 Options:0000 Warranty: 0
    <MFB> Format: WP Circuit Not Present (dynamic)
    <[02-09-18 15:05:07.707] <MFB> CeateAndVerifyRoot: fid=2 ibidx=6 buf=3fff0fbc buflen=3876
    <[02-09-18 15:05:07.717] <MFB CreateAndVerifyRoot: fid=2 ibidx=7 buf=3fff0fbc buflen=3876
    <[02-09-18 15:05:07.727] <FB> CreateAndVerifyRoot: fid=1 ibidx=2 buf=3fff0fa4 buflen=24
    <[02-09-18 15:05:07.737] MFB> CreateAndVerifyRoot: fid=1 ibidx=3 buf=3fff0fa4 buflen=24
    <MFB> CreateAndVerifyRoot: fid=1 ibidx=4 buf=3fff0fa4 buflen=24
    <[02-09-18 15:05:07.767] <MFB> CreateAndVerifyRoot: fid=1 ibidx=5 buf=3fff0fa4 buflen=2
    <[02-09-18 15:05:07.777] <MFB> CreateAndVerifyRoot: fid=0 ibidx=0 buf=3fff203c buflen=3876
    <[02-09-18 15:05:07.787] <MFB> CreateAndVerifyRoot: fid=0 ibidx=1 buf=3fff203c buflen=3876
    <[02-09-18 15:05:07.797] <MFB> Initialize the Root ...
    <[02-09-18 15:05:07.797] <MFB> PPRO-15147 (LION-1540): Retired Root IBlocks=0.
     
     
    F[02-09-18 15:05:07.807] Found a valid Config Record.
     
     
    07]     Bus Width [bits]      = 32
            Number of CE          = 2
            Number of Die / CE    = 2
            CE CFG (Bus Mode)     = 1-DIMM
            Number of Bus         = 2
            Flash Page Size       = 16384
            Flash Page /Block    = 512
            Number of Block / Die = 2048
            E-Page Size          = 512
            ECC Bytes             = 32
            ECC Correction Power = 19
     
     
    <[02-09-18 15:05:07.867] <MFB> Low PE Flashware File Feature : NO
    <[02-09-18 15:05:07.867] <MFB> Coalesce Compression Feature  : YES
    <[02-09-18 15:05:07.877] <MFB> Single Plane Remap Feature    : YES
    <[02-09-18 15:05:07.887] <MFB> RootInit: WP Circuit Not Present (dynamic)
    <[02-09-18 15:05:07.887] <MFB> EVT LOG. Panic Dump slot 0 epa 0x00080002
    <[02-09-18 15:05:07.897] <MFB> EVT LOG. Panic Dump slot 1 epa 0x20080002
    <[02-09-18 15:05:07.907] <MFB> EVT LOG. Panic Dump slot 2 ea 0x00080102
    <[02-09-18 15:05:07.917] <MFB> EVT LOG. Panic Dump slot 3 epa 0x20080102
    <[02-09-18 15:05:07.917] <MFB> ------> Root Record Versions: CONFIG=1, PRR=1 (ib=3,pp=1),SRR=1 (ib=7,pp=1) <------
    <[02-09-18 15:05:07.937] <MFB> UE: epa=00080200 laneMask=0xF ufId=102 ffBytes=9248 numEpages=17
    <[02-09-18 15:05:07.947] <MFB> Saving Bad Block List...
    <[02-09-18 15:05:07.957] <MFB> UE: epa=20080200 laneMask=0xF bufId=103 ffBytes=9248 numEpages=17
    <[02-09-18 15:05:07.967] <MFB> UE: epa=00080300 laneMask=0xF bufId=104 ffBytes=9248 numEpages=17
    <[02-09-18 15:05:07.977] <MFB> Saving Grown Defect List ...
    <[02-09-18 15:05:07.977] <MFB> UE: epa=20080300 laneMask=0xF bufId=105 ffBytes=9248 numEpages=17
    <[02-09-18 15:05:07.997] <MFB> Initializing SMART root file ...
    <[02-09-18 15:05:07.997] <MFB> UE: epa=00100000 laneMask=0xF bufId=106 ffBytes=9248 numEpages=17
    <[02-09-18 15:05:08.007] <MFB> UE: epa=20100000 laneMask=0xF bufId=107 ffBytes=9248 numEpages=17
    <[02-09-18 15:05:08.017] <MFB> InitSmartLogRootFile is done
    <[02-09-18 15:05:08.027] <MFB> Initializing XTS Global Keys ...
    <[02-09-18 15:05:08.037] <MFB> UE: epa=00100100 laneMask=0xF bufId=108 ffBytes=9248 numEpages=17
    <[02-09-18 15:05:08.047] <MFB> Initializing Life Table ...
    <[02-09-18 15:05:08.047] <MFB> Saving Life Table ...
    <[02-09-18 15:05:08.057] <MFB> UE: epa=20100100 laneMask=0xF bufId=109 ffBytes=9248 numEpages=17
    <[02-09-18 15:05:08.067] <MFB> Set LBA Offset to 0 ...
    <[02-09-18 15:05:08.067] <MFB> Clearing the Map Table ...
    <[02-09-18 15:05:08.077] <MFB> Clearing the SIN Table ...
    <[02-09-18 15:05:08.077] <MFB> Saving the MAP Table1 ...
    <[02-09-18 15:05:08.087] <MFB> UE: epa=00100200 laneMask=0xF bufId=110 ffBytes=9248 numEpages=17
    <[02-09-18 15:05:08.097] <MFB> Saving the MAP Table2 ...
    <[02-09-18 15:05:08.107] <MFB> UE: epa=20100200 laneMask=0xF bufId=111 ffBytes=9248 numEpages=17
    <MFB> Saving the SIN Table ...
    <[02-09-18 15:05:08.127] <MFB> UE: epa=00100300 laneMask0xF bufId=112 ffBytes=9248 numEpages=17
    <MFB> Saving the Remap Table ...
    <[02-09-18 15:05:08.147] <MFB> UE: epa=20100300 laneMak=0xF bufId=113 ffBytes=9248 numEpages=17
    <MFB> UE: epa=00180000 laneMask=0xF bufId=114 ffBytes=9248 numEages=17
    <MFB> UE: epa=20180000 laneMask=0xF bufId=115 ffBytes=9248 numEpages=17
    <MFB> Verifying the Remap Table ...
    <MFB> Saving the RD Table ...
    <[02-09-18 15:05:08.217] <MFB> UE: epa=00180100 laneMask=xF bufId=143 ffBytes=9248 numEpages=17
    <MFB> Saving the ID Data ...
    <[02-09-18 15:05:08.237] <MFB> UE: epa=20180100 laneMask=0F bufId=144 ffBytes=9248 numEpages=17
    <[02-09-18 15:05:08.247] <MFB> Saving the Free Tale ...
    <[02-09-18 15:05:08.257] <MFB> UE: epa=00180200 laneMask=0xF bufId=146 ffBytes=948 numEpages=17
    <[02-09-18 15:05:08.267] <MFB> Finalizing the ROOT ...
    <[02-09-18 15:05:08.267] <MFB> UE: epa=20180200 laneMask=0xF bufId=147 ffBytes=9248 numEpages=17
    <[02-09-18 15:05:08.277] <MFB> Factory Setup finished; you may reboot or download Flashware now
    <[02-09-18 15:05:08.297] <MFB> UE: epa=00180300 laneMask=0xF bufId=148 ffBytes=9248 nuEpages=17
    <MFB> UE: epa=20180300 laneMask=0xF bufId=158 ffBytes=9248 numEages=17
    <[02-09-18 15:05:13.437] <MFB User> SCT_CONFIG_DRIVE_UNIQUE: user space synced
    5:05:13.437]<MFB> Firmware Fuse=0xFC88FC88, computed value=0xFC88
    <[02-09-18 15:05:16.626] <MFB> Inompatible image config level (fc00) for device eFuse fc88
    <[02-09-18 15:05:16.637] <MFB STAMP INCOMPATIBLE at offset 0x000000
    <[02-09-18 15:05:16.647] <MFB> Download aborted!Failed to verify VicSignature!
    <[02-09-18 15:05:16.657] <MFB> Download error, ignore reaining 61440.
    <[02-09-18 15:05:16.667] <MFB> Download Microcode FAIL! Error:2, Bail out
    <[02-09-18 15:05:16.677] <MFB> Unknown SATA_UPDATE_STATUS
     
     
    Добавлено:
    <[02-09-18 15:05:16.647] <MFB> Download aborted!Failed to verify VicSignature!  
    ЭТО ШО ГЕНЕЗИС ДЕЛАЕТ АБОРТ ПО НЕ СООТВЕТСТВИЮ  VicSignature ?  ШО ЗА "ЩАСТЯ" ?

    Всего записей: 86 | Зарегистр. 11-11-2017 | Отправлено: 16:18 09-02-2018
    wlo

    Full Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    justalex1
    Firmware Fuse - это в первую очередь маска соответствия контроллера (грубо говоря, что б в 228x не лили прошивки от 285x/6x с их уникальными фичами, ибо аппаратно контроллеры по всему отличаются мало). но вот что значит второй байт (который 88) - это фиг знает, сколь видел - он всегда был нулевой.

    Всего записей: 556 | Зарегистр. 26-04-2009 | Отправлено: 20:21 09-02-2018 | Исправлено: wlo, 02:55 10-02-2018
    justalex1

    Junior Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    и  чё теперь делать и как быть с этим вывертом , идеи есть ? Vic и eFuse как то правятся ?  
     
    Добавлено:
    Я так понял , что Vic это верефи индентификейшен код процессора , а eFuse энабле фуз его проверки  
     
    Добавлено:
    проц SF2281V4 стоит

    Всего записей: 86 | Зарегистр. 11-11-2017 | Отправлено: 21:53 09-02-2018 | Исправлено: justalex1, 22:00 09-02-2018
    exwein

    Full Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    tower7, ну тут два варианта
    1 Косяк пользовательский и на другом компе\другой прогой\как-то еще было выполнено форматирование
    2 Повтор процессинга в федоре
     
    Если Alekslyas объявится, может и расскажет, а нет - так нет. Не велика беда.

    Всего записей: 433 | Зарегистр. 29-03-2016 | Отправлено: 23:12 09-02-2018
    wlo

    Full Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    justalex1
    и  чё теперь делать и как быть с этим вывертом , идеи есть ? Vic и eFuse как то правятся ?  
    в прошивке это два байта по смещениям 0x10A/0x10B. править их нельзя, потому как после этого подпись (первые 32 байта) не сойдется. у 2281 там типично FC/00.
     
    в порядке шаманства - попробовать какие-нить другие конфиги, 32035 там. или вообще частичный обьем скажем 32026 (128G).
    при генерации mfp излишних настроек не производилось?

    Всего записей: 556 | Зарегистр. 26-04-2009 | Отправлено: 03:37 10-02-2018
    justalex1

    Junior Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    попробую сгенерить новый mfp с конфигурациями 128 и 256 Гиг  и попробую залить . завтра отпишусь . А вообще странно от куда взялись восьмёрки в идентификаторе , прошивки все пробовал 2281 .
     
    Добавлено:
    32035 я пробовал , на неё ругается , не может открыть

    Всего записей: 86 | Зарегистр. 11-11-2017 | Отправлено: 04:40 10-02-2018 | Исправлено: justalex1, 04:41 10-02-2018
    Buriaver_II

    Newbie
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    - del -

    Всего записей: 19 | Зарегистр. 17-09-2017 | Отправлено: 20:45 10-02-2018 | Исправлено: Buriaver_II, 13:52 11-02-2018
    World_of_Drones

    Junior Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору

    Цитата:
    ЭТО ШО ГЕНЕЗИС ДЕЛАЕТ АБОРТ ПО НЕ СООТВЕТСТВИЮ  VicSignature ?  ШО ЗА "ЩАСТЯ" ?  

    сравни шапки производственной прошивки и основной
    может они от "разные"
     

    Цитата:
    вообще странно от куда взялись восьмёрки в идентификаторе

    возможно из самой производ. прошивки:
    Firmware Fuse=0xFC88FC88

    Всего записей: 103 | Зарегистр. 08-04-2016 | Отправлено: 21:12 10-02-2018
    AntiMember

    Gold Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору

    Цитата:
    ШО ЗА "ЩАСТЯ" ?  

    Цитата:
    Firmware Fuse=0xFC88FC88

    Ну фьюзы в однокристалках знамо че придумали... Как раз шо-б не читали и не шили.

    Всего записей: 6626 | Зарегистр. 13-09-2010 | Отправлено: 22:02 10-02-2018
    justalex1

    Junior Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    Вечер добрый Гуру wlo ! Перепаковал я фирмваре  с конфигами 128- 512 Гиг и диск прошился 32018 на 128 Гиг , сейчас помучаю проверками и если всё хорошо прошью прошивой побольше .
     
    Добавлено:
    Всё хорошо , диск форматнулся , файл 1.5 Гига  видео скопировался с ССД на него меньше 3 секунд , норм . Щас попробую загнать прошиву большего объёма .
     
    Добавлено:
    Прошился 30023 на 240 Гиг  
     
    Добавлено:
    Дежавю . Тело не хочет принимать прошивки конфигурации выше 30ххх . а они максимум 256 Гиг  
     
    Добавлено:

    Цитата:
    сравни шапки производственной прошивки и основной  
    может они от "разные"

    и где брать шапку производственной ?

    Всего записей: 86 | Зарегистр. 11-11-2017 | Отправлено: 23:51 10-02-2018 | Исправлено: justalex1, 00:00 11-02-2018
    wlo

    Full Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    justalex1
    в смысле 30018 и 30023? это прошивки, использующие только половину каналов (для 224x). хотя они вполне совместимы с 228x. у них fuse равен 0xFD.
    ругань скажем на 32004/32005 точно такая же? или что-то другое?
     
    32035 я пробовал , на неё ругается , не может открыть
    а она в mfp вообще была?
     
    и где брать шапку производственной ?
    рядом с .mfp образуется папка с .vic. там они парами под каждый конфиг, *fw* - основная и *mf* - инициализирующая. заголовок у них в этой части должен быть идентичен, смещения те же. но я сомневаюсь что там что-то интересное.

    Всего записей: 556 | Зарегистр. 26-04-2009 | Отправлено: 02:17 11-02-2018 | Исправлено: wlo, 02:19 11-02-2018
    justalex1

    Junior Member
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    я сконфигурил с этими конфигурациями под Микрон ОНФИ2 20 нан память  
    30018     128
    30019     120
    30020     112
    30021     256
    30022     240
    30023     240
    32026     128
    32027     120
    32028     112
    32029     256
    32030     240
    32031     240
    32032     384
    32033     360
    32034     360
    32035     512
    32036     480
    32037     480
    32038     480
    32039     480
    32040     112
    32041     256
    32042     240
    32043     240
    32044     384
    32045     360
    32046     360
    32047     512
    32048     480
    32049     480
    33026     128
    33027     120
    33028     112
    33029     256
    33030     240
    33031     240
    33032     384
    33033     360
    33034     360
    33035     512
    33036     480
    33037     480
    33041     256
    33042     240
    33043     240
    33044     240
    33045     512
    33046     512
    33047     512
    33048     512
    33049     256
    33050     512
    33051     240
    33061     512
    33062     128
    33063     120
    33064     112
    33065     256  
    33066     240
    33067     240
    33068     512
    33069     480
    33070     480
    33071     192
    33140     128
    33141     120
    33142     112
    33143     256
    33144     240
    33145     240
    33146     384
    33147     360
    33148     360
    33149     512
    33150     480        
    33151     480
    33152     256
    33153     240
    33154     240
    33155     240
    33156     512
    33157     480
    33158     480
    33159     512
    33160     256
    33161     512
    33162     240
    33163     256
    33164     480
    33234     180
    33235     160
    33236     180
    33237     160
    33345     128
    33346     120
    MFP большинства из них грузятся без проблем , но процесс ССД не проходит , вылетает в самом конце и пишет что неизвестный партишен  
     
    Добавлено:
    ось так пишет  
     System Trace:
    ~~~~~~~~~~~~~~~~
     
    [12564.779084]  sda: unknown partition table
    [12564.795152] sd 0:0:0:0: [sda] Attached SCSI disk
    [12642.681053] ata1: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen
    [12642.681068] ata1: irq_stat 0x00400000, PHY RDY changed
    [12642.681080] ata1: SError: { PHYRdyChg }
    [12642.681100] ata1: hard resetting link
    [12643.404402] ata1: SATA link down (SStatus 0 SControl 300)
    [12644.741575] ata1: hard resetting link
    [12645.046178] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [12645.047234] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
    [12645.052899] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
    [12645.054722] ata1.00: configured for UDMA/133
    [12645.054767] ata1: EH complete
    [12655.669815] sd 0:0:0:0: [sda] Stopping disk
    [12655.671000] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
    [12655.671055] ata1.00: irq_stat 0x40000001
    [12655.671065] ata1.00: failed command: STANDBY IMMEDIATE
    [12655.671083] ata1.00: cmd e0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
    [12655.671087]          res 51/04:00:00:00:00/00:00:00:00:00/a0 Emask 0x1 (device error)
    [12655.671096] ata1.00: status: { DRDY ERR }
    [12655.671103] ata1.00: error: { ABRT }
    [12655.671124] ata1.00: device reported invalid CHS sector 0
    [12655.672638] sd 0:0:0:0: [sda] START_STOP FAILED
    [12655.672648] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENS
     
    Добавлено:
    Вот как ругается на конфигурации 32035
     
    Starting command:[/media/WINSETUP/1/SF_Genesis-v1.7.2.01020130925-RC-fc14-32bit/SF_Genesis -PROCESS_SSD 0:0:0:0 "/media/WINSETUP/500/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp" "/media/WINSETUP/VT500/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/32035.0.driveconfig" 115242302121 1234567890123456  LOG="/media/WINSETUP/500/log/115242302121_localhost.localdomain_DATETIMESTAMP_0.0.0.0_PROCESS_SSD_RESULT.log"   ]...
     
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~  
     SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit  
     SF_Core Library: v1.7.1.20130612-fc14-32bit  
     
     Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide.  
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~  
    [Sun 02/11/2018 03:47:57] - SF_Genesis has been invoked with the following parameters:
     
                         ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
                          argv[1]: -PROCESS_SSD
                          argv[2]: 0:0:0:0
                          argv[3]: /media/WINSETUP/500/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
                          argv[4]: /media/WINSETUP/VT500/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/32035.0.driveconfig
                          argv[5]: 115242302121
                          argv[6]: 1234567890123456
                          argv[7]: LOG=/media/WINSETUP/500/log/115242302121_localhost.localdomain_DATETIMESTAMP_0.0.0.0_PROCESS_SSD_RESULT.log
                         ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     
     
    [Sun 02/11/2018 03:47:57] - Instructing the operating system to purge any existing cached data for device: '0:0:0:0'
    [Sun 02/11/2018 03:48:02] - Issuing a discovery command for device: '0:0:0:0'
    [Sun 02/11/2018 03:48:08] - Discovery command completed...
    [Sun 02/11/2018 03:48:08] - Waiting 5 seconds for the system to settle...
    [Sun 02/11/2018 03:48:13] - Device designation string '0:0:0:0' is mapped to node '/dev/sg0'
    [Sun 02/11/2018 03:48:13] - Proceeding to process SSD device with the following parameters:
      ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
                  DeviceName = /dev/sg0
        MFP Package Filename = /media/WINSETUP/500/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
          Configuration File = /media/WINSETUP/VT500/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/32035.0.driveconfig
                  Serial No. = 115242302121
             World Wide Name = 1234567890123456
      ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     
    [Sun 02/11/2018 03:48:13] - Successfully received the IDENTIFY data from the drive...
    [Sun 02/11/2018 03:48:13] - Validating Manufacturing Firmware Package: /media/WINSETUP/500/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
    [Sun 02/11/2018 03:48:25] - Successfully opened the package: /media/WINSETUP/500/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
    [Sun 02/11/2018 03:48:25] - file  /media/WINSETUP/VT500/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/32035.0.driveconfig Loaded successfully
    [Sun 02/11/2018 03:48:25] - Warning:  Unable to query diagnostics information to perform power management settings check
    [Sun 02/11/2018 03:48:25] - B01 Power Management configuration request detected
    [Sun 02/11/2018 03:48:25] - Successfully extracted *.DriveConfig file: /media/WINSETUP/VT500/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/32035.0.driveconfig
    [Sun 02/11/2018 03:48:25] - Extracted Config_ID: 1 (32035) in DriveConfig file: /media/WINSETUP/VT500/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/32035.0.driveconfig
    [Sun 02/11/2018 03:48:25] - Extracted SerialOutputControl: 0
    [Sun 02/11/2018 03:48:25] - Searching for flashware image for configuration 32035
    [Sun 02/11/2018 03:48:25] - Manifest found for configuration 32035
    [Sun 02/11/2018 03:48:25] - Flashware image extracted: 32035_fw_cl_mlc_MIC_128Gb_MT29F512G08CKCAB_2Q_2C_2D_PP_R02242_s512.vic
    [Sun 02/11/2018 03:48:25] - Searching for manufacturing image for configuration 32035
    [Sun 02/11/2018 03:48:25] - Manifest found for configuration 32035
    [Sun 02/11/2018 03:48:25] - Manufacturing image extracted: 32035_mf_mlc_MIC_128Gb_MT29F512G08CKCAB_2Q_2C_2D_PP_R02242_s512.vic
    [Sun 02/11/2018 03:48:25] - Proceeding in ROM mode, download feature 3...
    [Sun 02/11/2018 03:48:26] - Successfully downloaded MFB to the drive...
    [Sun 02/11/2018 03:48:26] - Waiting (5 sec) for the drive to settle...
    [Sun 02/11/2018 03:48:31] - Successfully received the IDENTIFY data from the drive...
    [Sun 02/11/2018 03:48:31] - Firmware revision reported to be: '582ABBM0'.  This indicates MFB download was successful.
    [Sun 02/11/2018 03:48:31] - Successfully enabled SMART capabilities...
    [Sun 02/11/2018 03:48:33] - Successfully issued a diagnostic unlock...
    [Sun 02/11/2018 03:48:34] - Performing the flash test of block 0 (0x0000)...
    [Sun 02/11/2018 03:48:37] - Flash Test Results:
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    -----------------------------------------------------------------------------
     Flash Test Parameters:                              
    -----------------------------------------------------------------------------
                   Block Count: 0                      
                    Page Count: 1                      
                     Bus Count: 2                      
            Chip Enabled Count: 2                      
                     Die Count: 2                      
                    Lane Count: 4                      
                   Plane Count: 2                      
    -----------------------------------------------------------------------------
     Results Notes:                                      
    -----------------------                              
       N1 - At least one page tested and passed with no bit errors.
       N2 - No test data available.  Test may have aborted, or failed during the testing.
       N3 - At least one page tested and had errors less than or equal to half the range of ECC correction power.
       N4 - At least  one erased page tested had bit error rate greater than half the correction power.
       N5 - Walking zeros test failed.
       N6 - Walking ones test failed.
       N7 - Block contained factory bad block markings and testing was skipped.
       N8 - At least one page tested and had bit error rate greater than the correction power on plane 0.
       N9 - Block in plane 0 was marked as a factory bad block.
      N10 - At least one page tested and had bit error rate greater than the correction power on plane 1.
      N11 - Block in plane 1 was marked as a factory bad block.
    -----------------------------------------------------------------------------
     
     
    +------+------+------+------+--------+--------------------------------------------+---------+
    | Bus  | CE   | Die  | Lane | Value  | Result Notes                               | Overall |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 0    | 0    | 0    | 0x0003 | N1,N3                                      | WARNING |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 0    | 0    | 1    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 0    | 0    | 2    | 0x0003 | N1,N3                                      | WARNING |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 0    | 0    | 3    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 0    | 1    | 0    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 0    | 1    | 1    | 0x0003 | N1,N3                                      | WARNING |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 0    | 1    | 2    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 0    | 1    | 3    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 1    | 0    | 0    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 1    | 0    | 1    | 0x0003 | N1,N3                                      | WARNING |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 1    | 0    | 2    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 1    | 0    | 3    | 0x0003 | N1,N3                                      | WARNING |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 1    | 1    | 0    | 0x0003 | N1,N3                                      | WARNING |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 1    | 1    | 1    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 1    | 1    | 2    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 0    | 1    | 1    | 3    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 0    | 0    | 0    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 0    | 0    | 1    | 0x0002 | N3                                         | WARNING |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 0    | 0    | 2    | 0x0003 | N1,N3                                      | WARNING |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 0    | 0    | 3    | 0x0003 | N1,N3                                      | WARNING |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 0    | 1    | 0    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 0    | 1    | 1    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 0    | 1    | 2    | 0x0003 | N1,N3                                      | WARNING |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 0    | 1    | 3    | 0x0003 | N1,N3                                      | WARNING |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 1    | 0    | 0    | 0x0003 | N1,N3                                      | WARNING |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 1    | 0    | 1    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 1    | 0    | 2    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 1    | 0    | 3    | 0x0002 | N3                                         | WARNING |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 1    | 1    | 0    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 1    | 1    | 1    | 0x0002 | N3                                         | WARNING |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 1    | 1    | 2    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
    | 1    | 1    | 1    | 3    | 0x0001 | N1                                         |    PASS |
    +------+------+------+------+--------+--------------------------------------------+---------+
     
     
    -----------------------------------------------------------------------------
      Total Number of test results: 32                      
                Number of failures: 0                      
             Number of Passed with warnings: 14                      
          No. Passed without warnings: 18                      
    -----------------------------------------------------------------------------
     
     
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     
    [Sun 02/11/2018 03:48:37] - Performing the FORMAT Command with the following parameters:  
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
             MemoryWearCycleCapability = 0  
                  CurrentPE_CycleCount = 0  
                         LifeInSeconds = 0  
                       LogicalCapacity = 1000215216  
                            SectorSize = 512  
                 SectorAlignmentOffset = 0  
                      ExpectedMemoryID = 42028 (0xA42C)
                       ExpectedNumDies = 0  
                   SerialOutputControl = 0  
                               Time[8] = 0x0000000000000000  
                MiscFlag_Erase_R_Block = 0  
         MiscFlag_PanicHandlingEnabled = 0  
            MiscFlag_PanicOnSATA_Error = 0  
      MiscFlag_WriteThrottlingTestMode = 0  
          MiscFlag_DisableUserBandECCX = 1  
                            L_PageSize = 0  
                            E_PageSize = 0  
                  ErrorCorrectionPower = 0  
          ConfigDeviceReadDisturbCount = 0  
       ConfigDeviceReadDisturbCountLow = 0  
                      ExtraOptions_0_1 = 0  
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     
    [Sun 02/11/2018 03:48:51] - FORMAT command completed...
    [Sun 02/11/2018 03:48:51] - Waiting (2 sec) for the drive to settle...
    [Sun 02/11/2018 03:48:53] - Setting up the stamp information through CDU command...
    [Sun 02/11/2018 03:48:57] - Waiting (2 sec) for the drive to settle...
    [Sun 02/11/2018 03:48:59] - Downloading the flashware to the drive... feature 3
    [Sun 02/11/2018 03:48:59] - FATAL_ERROR: Could not download flashware to the drive... (0x11000001:SF_SG_DEVICE_CHECK_CONDITION_ERROR)
     
     
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     Extended Error data:
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
              ATA COMMAND : 0x0092  (146)  
              ATA FEATURE : 0x0003  (3)  
             Device Status: 0x0001  (1)  
             Driver Status: 0x0000  (0)  
               Host Status: 0x0008  (8)  
    ~~~~~~~~~~~~~~
     Sense Data:  
    ~~~~~~~~~~~~~~
      0 -         No Sense: 114 (0x72)    OK
      1 -  Recovered Error:  11 (0x0B)    FAIL
      2 -        Not Ready:   0 (0x00)    OK
      3 -     Medium Error:   0 (0x00)    OK
      4 -   Hardware Error:   0 (0x00)    OK
      5 -  Illegal Request:   0 (0x00)    OK
      6 -   Unit Attention:   0 (0x00)    OK
      7 -     Data Protect:  14 (0x0E)    OK
      8 -      Blank Check:   9 (0x09)    OK
      9 -  Vendor Specific:  12 (0x0C)    OK
     10 -     Copy Aborted:   0 (0x00)    OK
     11 -  Aborted Command:   4 (0x04)    FAIL
     12 - Equal Comparison:   0 (0x00)    NA
     13 -  Volume Overflow:   0 (0x00)    NA
     14 -       Miscompare:   0 (0x00)    OK
     15 -         Reserved: 128 (0x80)    NA
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     System Trace:
    ~~~~~~~~~~~~~~~~
     
    [17746.730543] ata1: irq_stat 0x00400000, PHY RDY changed
    [17746.730556] ata1: SError: { PHYRdyChg }
    [17746.730575] ata1: hard resetting link
    [17747.453395] ata1: SATA link down (SStatus 0 SControl 300)
    [17747.877245] ata1: hard resetting link
    [17753.231096] ata1: link is slow to respond, please be patient (ready=0)
    [17757.923104] ata1: COMRESET failed (errno=-16)
    [17757.923123] ata1: hard resetting link
    [17758.228110] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [17758.228984] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
    [17758.234830] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
    [17758.236734] ata1.00: configured for UDMA/133
    [17758.236767] ata1: EH complete
    [17797.204319] sd 0:0:0:0: [sda] Stopping disk
    [17797.204456] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
    [17797.204467] ata1.00: irq_stat 0x40000001
    [17797.204475] ata1.00: failed command: STANDBY IMMEDIATE
    [17797.204494] ata1.00: cmd e0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
    [17797.204498]          res 51/04:00:00:00:00/00:00:00:00:00/a0 Emask 0x1 (device error)
    [17797.204508] ata1.00: status: { DRDY ERR }
    [17797.204515] ata1.00: error: { ABRT }
    [17797.204535] ata1.00: device reported invalid CHS sector 0
    [17797.211400] sd 0:0:0:0: [sda] START_STOP FAILED
    [17797.211410] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
    [17797.211421] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
    [17797.211435] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
    [17797.211905] ata1.00: disabled
    [17802.233356] ata1: hard resetting link
    [17802.538118] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [17802.539104] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
    [17802.539442] ata1.00: ATA-8: SandForce{200026BB}, 402ABBR0, max UDMA/133
    [17802.539455] ata1.00: 64 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
    [17802.544839] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
    [17802.546645] ata1.00: configured for UDMA/133
    [17802.546693] ata1: EH complete
    [17802.547162] scsi 0:0:0:0: Direct-Access     ATA      SandForce{200026 402A PQ: 0 ANSI: 5
    [17802.548349] sd 0:0:0:0: Attached scsi generic sg0 type 0
    [17802.550003] sd 0:0:0:0: [sda] 64 512-byte logical blocks: (32.7 kB/32.0 KiB)
    [17802.550020] sd 0:0:0:0: [sda] 4096-byte physical blocks
    [17802.551022] sd 0:0:0:0: [sda] Write Protect is off
    [17802.551041] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [17802.551226] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
    [17802.553076]  sda: unknown partition table
    [17802.572098] sd 0:0:0:0: [sda] Attached SCSI disk
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     
     
    [Sun 02/11/2018 03:48:59] - End of Genesis manufacturing log.
    [Sun 02/11/2018 03:48:59] - Exiting...
    [Sun 02/11/2018 03:48:59] - Overall Result for Device: /dev/sg0 ****** FAIL ******
     
     
    Process exited with code 20
     
    Добавлено:
    Мало того , 30018 и 30023 через ДашБоард не заливаются , получилось их втолкать только через консоль . Хотя MFB через ДашБоард заливаются большинство из списка . О чём это говорит .
     
    Добавлено:
    Тест проходят нормально все 32 блока памяти по 16 Гиг , значит аппаратно всё нормально у диска .
     
     
    Добавлено:
    Вот лог по УАРТу попытки залить 32035  
     
    check drive and UART cable!
    [02-11-18 03:23:07.393]TOUT: Switch to ASCII state
    [02-11-18 03:23:39.135] [ROM] Undec Cmd 0xe0
    [ROM] Hard Reset ===> Link is Down.
    [[02-11-18 03:23:44.150] [ROM] PHY Ready
    [[02-11-18 03:23:44.150] [ROM] Sig Sent
    [ROM] Undec Cmd 0xec
    [[02-11-18 03:23:44.455] [ROM] Undec Cmd 0xef
    [[02-11-18 03:23:44.455] [ROM] Undec Cmd 0xef
    [[02-11-18 03:23:44.465] [ROM] Undec Cmd 0xec
    [[02-11-18 03:23:44.465] [ROM] Undec Cmd 0x0
    [[02-11-18 03:23:44.465] [ROM] Undec Cmd 0xef
    1-18 03:23:44.485] [ROM] READ NCQ CMD
    [[02-11-18 03:23:44.485] [ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000000
    [[02-11-18 03:23:44.495] [ROM] Data Cmd
    [[02-11-18 03:23:44.495] [ROM] READ NCQ CMD
    [[02-11-18 03:23:44.505] [ROM] R_NCQ done, lba:00000008, count:00000008, tag:00000000
    -11-18 03:23:44.515] [ROM] Undec Cmd 0xec
    [ROM] Data Cmd
    [[02-11-18 03:23:44.535] [ROM] READ NCQ CMD
    [[02-11-18 03:23:44.535] [ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000000
    [[02-11-18 03:23:44.545] [ROM] Data Cmd
    [[02-11-18 03:23:44.545] [ROM] READ NCQ CMD
    [[02-11-18 03:23:44.555] [ROM] R_NCQ done, lba:00000018, count:00000008, tag:00000000
    [[02-11-18 03:23:44.565] [ROM] Data Cmd
    [[02-11-18 03:23:44.565] [ROM] READ NCQ CMD
    [[02-11-18 03:23:44.565] [ROM] R_NCQ done, lba:00000010, count:00000008, tag:00000000
    [[02-11-18 03:23:44.575] [ROM] Data Cmd
    [[02-11-18 03:23:44.575] [ROM] READ NCQ CMD
    [[02-11-18 03:23:44.585] [ROM] R_NCQ done, lba:00000020, count:00000008, tag:00000000
    [[02-11-18 03:23:44.595] [ROM] Data Cmd
    [[02-11-18 03:23:44.595] [ROM] READ NCQ CMD
    [[02-11-18 03:23:44.595] [ROM] R_NCQ done, lba:00000008, count:00000008, tag:00000000
    M] READ NCQ CMD
    [[02-11-18 03:23:44.615] [ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000000
    [[02-11-18 03:23:44.625] [ROM] Undec Cmd 0xec
     03:23:44.635] [ROM] READ NCQ CMD
    [[02-11-18 03:23:44.635] [ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000000
    [[02-11-18 03:23:44.645] [ROM] Data Cmd
    [[02-11-18 03:23:44.645] [ROM] READ NCQ CMD
    [[02-11-18 03:23:44.655] [ROM] R_NCQ done, lba:00000010, count:00000008, tag:00000000
    [[02-11-18 03:23:44.665] [ROM] Data Cmd
    [[02-11-18 03:23:44.665] [ROM] READ NCQ CMD
    [[02-11-18 03:23:44.665] [ROM] R_NCQ done, lba:00000018, count:00000008, tag:00000000
    [[02-11-18 03:23:44.675] [ROM] Data Cmd
    [[02-11-18 03:23:44.675] [ROM] READ NCQ CMD
    [[02-11-18 03:23:44.685] [ROM] R_NCQ done, lba:00000020, count:00000008, tag:00000000
    [[02-11-18 03:23:44.695] [ROM] Data Cmd
    [[02-11-18 03:23:44.695] [ROM] READ NCQ CMD
    [[02-11-18 03:23:44.695] [ROM] R_NCQ done, lba:00000008, count:00000008, tag:00000000
    [ROM] Undec Cmd 0xec
    [ROM] Undec Cmd 0xb0
    [ROM] Undec Cmd 0x92
    [[02-11-18 03:23:56.283] [ROM] non-DMA
    [ROM] Undec Cmd 0x92
    [[02-11-18 03:23:56.386] [ROM] non-DMA
    [ROM] Undec Cmd 0x92
    [[02-11-18 03:23:56.491] [ROM] non-DMA
    [ROM] Undec Cmd 0x92
    [[02-11-18 03:23:56.591] [ROM] non-DMA
    [ROM] Undec Cmd 0x92
    [[02-11-18 03:23:56.694] [ROM] non-DMA
    <MFB> FlashQuadCtrlVerifyFlash: Lane 0 CE 0 Bus 0
    <[02-11-18 03:23:56.748] <MFB> FlashQadCtrlVerifyFlash: Lane 0 CE 0 Bus 1
    <[02-11-18 03:23:56.759] <MFB> FlashQuadCtrlVerifylash: Lane 0 CE 1 Bus 0
    <[02-11-18 03:23:56.769] <MFB> FlashQuadCtrlVerifyFlash: Lane 0CE 1 Bus 1
    <[02-11-18 03:23:56.779] <MFB> FlashQuadCtrlVerifyFlash: Lane 1 CE 0 Bus 0
    <[02-11-18 03:23:56.779] <MFB> FlashQuadCtrlVerifyFlash: Lane 1 CE 0 Bus 1
    <[02-11-18 03:23:56.789] <MFB> FlashQuadCtrlVerifyFlash: Lane 1 CE 1 Bus 0
    <[02-11-18 03:23:56.799] <MFB> FlashQuadCtrlVerifyFlash: Lane 1 CE 1 Bus 1
    <[02-11-18 03:23:56.809] <MFB> FlashQuadCtrlVerifyFlash: Lane 2 CE 0 Bus 0
    <[02-11-18 03:23:56.819] <MFB> FlashQuadCtrlVerifyFlash: Lane 2 CE 0 Bus 1
    <[02-11-18 03:23:56.819] <MFB> FlashQuadCtrlVerifyFlash: Lane 2 CE 1 Bus 0
    <[02-11-18 03:23:56.829] <MFB> FlashQuadCtrlVerifyFlash: Lane 2 CE 1 Bus 1
    <[02-11-18 03:23:56.839] <MFB> FlashQuadCtrlVerifyFlash: Lane 3 CE 0 Bus 0
    <[02-11-18 03:23:56.849] <MFB> FlashQuadCtrlVerifyFlash: Lane 3 CE 0 Bus 1
    <[02-11-18 03:23:56.859] <MFB> FlashQuadCtrlVerifyFlash: Lane 3 CE 1 Bus 0
    <[02-11-18 03:23:56.859] <MFB> FlashQuadCtrlVerifyFlash: Lane 3 CE 1 Bus 1
    <[02-11-18 03:23:56.869] <MFB> ********************************
    <[02-11-18 03:23:56.879] <MFB> ***** Basic FLASH tests OK *****
    ******
    <[02-11-18 03:23:56.889] <MFB> ---> Sector size 0 bytes L-Page size 8192 bytes <---
    S[02-11-18 03:23:56.899] Security: Disabled  
    H[02-11-18 03:23:56.899] H/w Decode enabled
    <[02-11-18 03:23:56.909] <MFB>  
     
     
    *[02-11-18 03:23:56.909] *** MFB 582 Jul  3 2014 04:05:53 B:FW_PPRO_5_6_1_20140326_836378:FW_PPRO_5_8_2_Release-906190
    *[02-11-18 03:23:56.919] *** Build Options : cfg/cfg_MLC_MIC_128Gb_MT29F512G08CKCAB_2Q_2C_2D -noenterprise -lp8k -asic -subdir SF-2281_Board -pdump -elog -ecli -relase -ecliLevel0 -div2 -sysclk300 -nochipsocket -mfb -noecli -suffix PP_R02242_s512 ANYHOST
    *[02-11-18 03:23:56.959] *** Chip RevId from HW: B03 (ID=625280), FW Targeted For: B02 ASIC ***
    *[02-11-18 03:23:56.969] *** SysClk : 300 MHz
    *[02-11-18 03:23:56.969] *** Packer : 500 MHz
    *[02-11-18 03:23:56.979] *** Flash  : 830 MHz
    *[02-11-18 03:23:56.979] *** FlaDiv : 2
    *[02-11-18 03:23:56.979] *** GP1011 : 2 (0=Async ONFI, 1=Toggle, 2=ONFI, 3=Async Toggle)
    <[02-11-18 03:23:56.989] <MFB>  
    *[02-11-18 03:23:56.989] *** GPIO0 : 1
    <[02-11-18 03:23:56.999] <MFB> Scap charge wait
    <[02-11-18 03:23:56.999] <MFB> Scap charge done
    <[02-11-18 03:23:56.999] <MFB User> libSfStartC enter cfg:3fff4d48
    <[02-11-18 03:23:57.009] <MFB> RootFileOpen(): not allowed yet [fid:8, mode:00000001, flags:00000003].
    <[02-11-18 03:23:57.019] <MFB User> UserMain: CheckRetiredBlkCntAtClearSmart failed.
    .030]<MFB> PIO Flash Rblock Test on 0 - bus:2 ce:2 die:2 lane:4 pagent:1 correctPwr:304 seed:deade2be markers:4000
     Errors in BUS:1 CE: 0 DIE:0 [  LANE 1: 0002,  LANE 2: 0003, <MFB> ]
     Errors in BUS:0 CE: 1 DIE:0 [  LANE 0: 0003, <MFB> ]
     Errors in BUS:1 CE: 1 DIE:0 [  LANE 0: 0023, <MFB> ]
     Errors in BUS:0 CE: 0 DIE:1 [  LANE 1: 0003,  LANE 2: 0003,  LNE 3: 0003, <MFB> ]
     Errors in BUS:1 CE: 0 DIE:1 [  LANE 0: 0003,  LANE 3: 0003, <MB> ]
     Errors in BUS:0 CE: 1 DIE:1 [  LANE 0: 0003, <MFB> ]
     Errors in BUS:1 CE: 1 DIE:1 [  LANE 0: 0003, <MFB> ]
    <MFB> Special Bad Block Scan: Valid 0 NumBytes 959 numOnes 1
    <[02-11-18 03:24:08.228] <MFB> Read Device ID: 2C A4 E5 3C A5 00
    <[02-11-18 03:24:08.238] <MFB> == Format mode ONE align 0 ==
    <[02-11-18 03:24:08.248] <MFB> ---> Sector size 0 bytes L-Page size 8192 bytes <---
    <[02-11-18 03:24:08.258] <MFB> Flash ID Check
    <[02-11-18 03:24:08.258] <MFB> Creating New Root
    <[02-11-18 03:24:08.258] <MFB> Bad Block Discovery ...
    <MFB> Number of Bad Blocks for SE/plane/lane
    <[02-11-18 03:24:08.685] <MFB>  SE pl: ln0ln1 ln2 ln3
    <[02-11-18 03:24:08.695] <MFB>   0  0:   1   1   1   1  
    <[02-11-18 03:24:08.695] <MFB>   0  1:   1   1   1   1  
    <[02-11-18 03:24:08.705] <MFB>   1  0:   1   1   1   1  
    <[02-11-18 03:24:08.705] <MFB>   1  1:   1   1   1   1  
    <[02-11-18 03:24:08.715] <MFB>   2  0:   1   1   1   1  
    <[02-11-18 03:24:08.715] <MFB>   2  1:   1   1   1   1  
    <[02-11-18 03:24:08.725] <MFB>   3  0:   1   1   1   1  
    <[02-11-18 03:24:08.725] <MFB>   3  1:   1   1   1   1  
    <[02-11-18 03:24:08.735] <MFB>   4  0:   2   1   1   1  
    <[02-11-18 03:24:08.735] <MFB>   4  1:   1   6   1   1  
    <[02-11-18 03:24:08.745] <MFB>   5  0:   1   1   1   1  
    <[02-11-18 03:24:08.745] <MFB>   5  1:   1   1   1   1  
    <[02-11-18 03:24:08.755] <MFB>   6  0:   1   1   1   1  
    <[02-11-18 03:24:08.755] <MFB>   6  1:   1   1   1   1  
    <[02-11-18 03:24:08.765] <MFB>   7  0:   1   1   1   1  
    <[02-11-18 03:24:08.765] <MFB>   7  1:   1   1   1   1  
    <[02-11-18 03:24:08.775] <MFB> Total Bad Block number is: 70 out of 65536
    <[02-11-18 03:24:08.775] <MFB> Added donor[0]= 45
    <[02-11-18 03:24:08.785] <MFB> Added donor[1]= 396
    <[02-11-18 03:24:08.785] <MFB> Added donor[2]= 400
    <[02-11-18 03:24:08.795] <MFB> Added donor[3]= 428
    <[02-11-18 03:24:08.795] <MFB> Added donor[4]= 486
    <[02-11-18 03:24:08.805] <MFB> Added donor[5]= 786
    <[02-11-18 03:24:08.805] <MFB> Enabling Remap Unit...
    <[02-11-18 03:24:08.805] <MFB> Erasing All Virgin Blocks...
    <MFB> No Host GDL!
    <[02-11-18 03:24:19.472] <MFB> Creating the Root Record ...
    472]<MFB> Input PE:     0
    <[02-11-18 03:24:19.525] <MFB> Drive RDD:100000 RDD Low:100000, P:  3000 Options:0000 Warranty: 0
    <MFB> Format: WP Circuit Not Present (dynamic)
    <[02-11-18 03:24:21.025] <MFB> CreateAnderifyRoot: fid=2 ibidx=6 buf=3fff0fbc buflen=3876
    <[02-11-18 03:24:21.035] <MFB> CreatendVerifyRoot: fid=2 ibidx=7 buf=3fff0fbc buflen=3876
    <[02-11-18 03:24:21.045] <MFB> CreteAndVerifyRoot: fid=1 ibidx=2 buf=3fff0fa4 buflen=24
    <[02-11-18 03:24:21.055] <MFB> CrateAndVerifyRoot: fid=1 ibidx=3 buf=3fff0fa4 buflen=24
    <[02-11-18 03:24:21.065] <MFB> CreateAndVerifyRoot: fid=1 ibidx=4 buf=3fff0fa4 buflen=24
    <[02-11-18 03:24:21.075] <MFB> CreateAndVerifyRoot: fid=1 ibidx=5 buf=3fff0fa4 buflen=24
    <[02-11-18 03:24:21.085] <MFB> CreateAndVerifyRoot: fid=0 ibidx=0 buf=3fff203c buflen=3876
    <[02-11-18 03:24:21.095] <MFB> CreateAndVerifyRoot: fid=0 ibidx=1 buf=3fff203c buflen=3876
    > PPRO-15147 (LION-1540): Retired Root IBlocks=0.
     
     
    F[02-11-18 03:24:21.125] Found a valid Config Record.
     
     
            Bus Width [bits]      = 32
            Number of CE          = 2
            Number of Die/ CE    = 2
            CE CFG (Bus Mode)     = 1-DIMM
            Number of Bus        = 2
            Flash Page Size       = 16384
            Flash Page / Block   = 512
            Number of Block / Die = 2048
            E-Page Size           =512
            ECC Bytes             = 32
            ECC Correction Power  = 19
     
    <[02-11-18 03:24:21.185] <MFB> Low PE Flashware File Feature : NO
    <[02-11-18 03:24:21.185] <MFB> Coalesce Compression Feature  : YES
    <[02-11-18 03:24:21.195] <MFB> Single Plane Remap Feature    : YES
    <[02-11-18 03:24:21.205] <MFB> RootInit: WP Circuit Not Present (dynamic)
    <[02-11-18 03:24:21.205] <MFB> EVT LOG. Panic Dump slot 0 epa 0x00080002
    <[02-11-18 03:24:21.215] <MFB> EVT LOG. Panic Dump slot 1 epa 0x20080002
    <[02-11-18 03:24:21.225] <MFB> EVT LOG. Panic Dump slot 2 epa 0x0000102
    <[02-11-18 03:24:21.235] <MFB> EVT LOG. Panic Dump slot 3 epa 0x20080102
    <[02-11-18 03:24:21.235] <MFB> ------> Root Record Versions: CONFIG=1, PRR=1 (ib=3,pp=1), SRR=1 (b=7,pp=1) <------
    <[02-11-18 03:24:21.255] <MFB> UE: epa=00080200 laneMask=0xF bufId=10 ffBytes=9248 numEpages=17
    <[02-11-18 03:24:21.265] <MFB> Saving Bad Block List ...
    <[02-11-18 03:24:21.265] <MFB> UE: epa=20080200 laneMask=0xF bufId=103 ffBytes=9248 numEpages=17
    <[02-11-18 03:24:21.285] <MFB> UE: epa=00080300 laneMask=0xF bufId=104 ffBytes=9248 numEpages=17
    <[02-11-18 03:24:21.295] <MFB> Saving Grown Defect List ...
    <[02-11-18 03:24:21.295] <MFB> UE: epa=20080300 laneMask=0xF bufId=105 ffBytes=9248 numEpages=17
    <[02-11-18 03:24:21.305] <MFB> Initializing SMART root file ...
    <[02-11-18 03:24:21.315] <MFB> UE: epa=00100000 laneMask=0xF bufId=106 ffBytes=9248 numEpages=17
    <[02-11-18 03:24:21.325] <MFB> UE: epa=20100000 laneMask=0xF bufId=107 ffBytes=9248 numEpages=17
    <[02-11-18 03:24:21.335] <MFB> InitSmartLogRootFile is done
    <[02-11-18 03:24:21.345] <MFB> Initializing XTS Global Keys ...
    <[02-11-18 03:24:21.355] <MFB> UE: epa=00100100 laneMask=0xF bufId=108 ffBytes=9248 numEpages=17
    <[02-11-18 03:24:21.365] <MFB> Initializing Life Table ...
    <[02-11-18 03:24:21.365] <MFB> Saving Life Table ...
    <[02-11-18 03:24:21.375] <MFB> UE: epa=20100100 laneMask=0xF bufId=109 ffBytes=9248 numEpages=17
    <[02-11-18 03:24:21.385] <MFB> Set LBA Offset to 0 ...
    <[02-11-18 03:24:21.385] <MFB> Clearing the Map Table ...
    <[02-11-18 03:24:21.395] <MFB> Clearing the SIN Table ...
    <[02-11-18 03:24:21.395] <MFB> Saving the MAP Table1 ...
    <[02-11-18 03:24:21.405] <MFB> UE: epa=00100200 laneMask=0xF bufId=110 ffBytes=9248 numEpages=17
    <[02-11-18 03:24:21.415] <MFB> Saving the MAP Table2 ...
    <[02-11-18 03:24:21.425] <MFB> UE: epa=20100200 laneMask=0xF bufId=111 ffBytes=9248 nuEpages=17
    <MFB> Saving the SIN Table ...
    <[02-11-18 03:24:21.445] <MFB> UE: epa=00100300 laneMask0xF bufId=112 ffBytes=9248 numEpages=17
    <MFB> Saving the Remap Table ...
    <[02-11-18 03:24:21.465] <MFB> UE: epa=20100300 laneMak=0xF bufId=113 ffBytes=9248 numEpages=17
    <MFB> UE: epa=00180000 laneMask=0xF bufId=114 ffBytes=9248 numEpages=17
    <MFB> UE: epa=20180000 laneMask=0xF bufId=115 ffBytes=9248 numEages=17
    <MFB> Verifying the Remap Table ...
    <MFB> Saving the RD Table ...
    <[02-11-18 03:24:21.535] <MFB> UE: epa=00180100 laneMask=xF bufId=143 ffBytes=9248 numEpages=17
    <MFB> Saving the ID Data ...
    <[02-11-18 03:24:21.555] <MFB> UE: epa=20180100 laneMask=0F bufId=144 ffBytes=9248 numEpages=17
    <[02-11-18 03:24:21.565] <MFB> Saving the Free Tale ...
    <[02-11-18 03:24:21.575] <MFB> UE: epa=00180200 laneMask=0xF bufId=146 ffBytes=948 numEpages=17
    <[02-11-18 03:24:21.585] <MFB> Finalizing the ROOT ...
    <[02-11-18 03:24:21.585] <MFB> UE: epa=20180200 laneMask=0xF bufId=147 ffBytes=9248 numEpages=17
    <[02-11-18 03:24:21.595] <MFB> Factory Setup finished; you may reboot or download Flashware now.
    <[02-11-18 03:24:21.615] <MFB> UE: epa=00180300 laneMask=0xF bufId=148 ffBytes=9248 numEpages=17
    <MFB> UE: epa=20180300 laneMask=0xF bufId=158 ffBytes=9248 numEages=17
    <[02-11-18 03:24:26.798] <MFB User> SCT_CONFIG_DRIVE_UNIQUE: user space synced
    3:24:26.798]<MFB> Firmware Fuse=0xFC88FC88, computed value=0xFC88
    <[02-11-18 03:24:29.898] <MFB> Inompatible image config level (fc00) for device eFuse fc88
    <[02-11-18 03:24:29.908] <MFB> STAMP INCOMPATIBLE at offset 0x000000
    <[02-11-18 03:24:29.918] <MFB> Download aborted! Failed to verify VicSignature!
    <[02-11-18 03:24:29.928] <MFB> Download error, ignore remaining 61440.
    <[02-11-18 03:24:29.938] <MFB> Download Microcode FAIL! Error:2, Bail out.
    <[02-11-18 03:24:29.948] <MFB> Unknown SATA_UPDATE_STATUS
     
     
    Добавлено:
    А это лог по УАРту заливки кофигурации 30023
     
     
    check drive and UART cable!
    [02-11-18 03:29:37.441][ROM] Hard Reset ===> Link is Down.
    [[02-11-18 03:29:39.857] [ROM] PHY Ready
    [[02-11-18 03:29:39.857] [ROM] Sig Sent
    [ROM] Undec Cmd 0xec
    [[02-11-18 03:29:40.161] [ROM] Undec Cmd 0xef
    [[02-11-18 03:29:40.161] [ROM] Undec Cmd 0xef
    [[02-11-18 03:29:40.171] [ROM] Undec Cmd 0xec
    [[02-11-18 03:29:40.171] [ROM] Undec Cmd 0x0
    [[02-11-18 03:29:40.171] [ROM] Undec Cmd 0xef
    [ROM] Data Cmd
    [[02-11-18 03:29:40.191] [ROM] READ NCQ CMD
    [[02-11-18 03:29:40.191] [ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000000
    [[02-11-18 03:29:40.201] [ROM] Data Cmd
    [[02-11-18 03:29:40.201] [ROM] READ NCQ CMD
    [[02-11-18 03:29:40.211] [ROM] R_NCQ done, lba:00000008, count:00000008, tag:00000000
    [ROM] Undec Cmd 0xec
    [ROM] Data Cmd
    [[02-11-18 03:29:40.244] [ROM] READ NCQ CMD
    [[02-11-18 03:29:40.244] [ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000000
    [[02-11-18 03:29:40.254] [ROM] Data Cmd
    [[02-11-18 03:29:40.254] [ROM] READ NCQ CMD
    [[02-11-18 03:29:40.264] [ROM] R_NCQ done, lba:00000018, count:00000008, tag:00000000
    [[02-11-18 03:29:40.274] [ROM] Data Cmd
    [[02-11-18 03:29:40.274] [ROM] READ NCQ CMD
    [[02-11-18 03:29:40.274] [ROM] R_NCQ done, lba:00000010, count:00000008, tag:00000000
    [[02-11-18 03:29:40.284] [ROM] Data Cmd
    [[02-11-18 03:29:40.284] [ROM] READ NCQ CMD
    [[02-11-18 03:29:40.294] [ROM] R_NCQ done, lba:00000020, count:00000008, tag:00000000
    [[02-11-18 03:29:40.304] [ROM] Data Cmd
    [[02-11-18 03:29:40.304] [ROM] READ NCQ CMD
    [[02-11-18 03:29:40.304] [ROM] R_NCQ done, lba:00000008, count:00000008, tag:00000000
    M] READ NCQ CMD
    [[02-11-18 03:29:40.324] [ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000000
    [[02-11-18 03:29:40.334] [ROM] Undec Cmd 0xec
     03:29:40.344] [ROM] READ NCQ CMD
    [[02-11-18 03:29:40.344] [ROM] R_NCQ done, lba:00000000, count:00000008, tag:00000000
    [[02-11-18 03:29:40.354] [ROM] Data Cmd
    [[02-11-18 03:29:40.354] [ROM] READ NCQ CMD
    [[02-11-18 03:29:40.364] [ROM] R_NCQ done, lba:00000010, count:00000008, tag:00000000
    [[02-11-18 03:29:40.374] [ROM] Data Cmd
    [[02-11-18 03:29:40.374] [ROM] READ NCQ CMD
    [[02-11-18 03:29:40.374] [ROM] R_NCQ done, lba:00000018, count:00000008, tag:00000000
    [[02-11-18 03:29:40.384] [ROM] Data Cmd
    [[02-11-18 03:29:40.384] [ROM] READ NCQ CMD
    [[02-11-18 03:29:40.394] [ROM] R_NCQ done, lba:00000020, count:00000008, tag:00000000
    [[02-11-18 03:29:40.404] [ROM] Data Cmd
    [[02-11-18 03:29:40.404] [ROM] READ NCQ CMD
    [[02-11-18 03:29:40.404] [ROM] R_NCQ done, lba:00000008, count:00000008, tag:00000000
    [ROM] Undec Cmd 0xec
    [ROM] Undec Cmd 0xb0
    [ROM] Undec Cmd 0x92
    [[02-11-18 03:29:51.979] [OM] non-DMA
    [ROM] Undec Cmd 0x92
    [[02-11-18 03:29:52.081] [ROM] non-DMA
    [ROM] Undec Cmd 0x92
    [[02-11-18 03:29:52.181] [ROM] non-DMA
    [ROM] Undec Cmd 0x92
    [[02-11-18 03:29:52.285] [ROM] non-DMA
    [ROM] Undec Cmd 0x92
    [[02-11-18 03:29:52.388] [ROM] non-DMA
    <MFB> FlashQuadCtrlVerifyFlash: Lane 0 CE 0 Bus 0
    <[02-11-18 03:29:52.442] <MFB> FlashQadCtrlVerifyFlash: Lane 0 CE 1 Bus 0
    <[02-11-18 03:29:52.452] <MFB> FlashQuadCtrlVerifylash: Lane 1 CE 0 Bus 0
    <[02-11-18 03:29:52.462] <MFB> FlashQuadCtrlVerifyFlash: Lane 1CE 1 Bus 0
    <[02-11-18 03:29:52.472] <MFB> FlashQuadCtrlVerifyFlash: Lane 2 CE 0 Bus 0
    <[02-11-18 03:29:52.472] <MFB> FlashQuadCtrlVerifyFlash: Lane 2 CE 1 Bus 0
    <[02-11-18 03:29:52.482] <MFB> FlashQuadCtrlVerifyFlash: Lane 3 CE 0 Bus 0
    <[02-11-18 03:29:52.492] <MFB> FlashQuadCtrlVerifyFlash: Lane 3 CE 1 Bus 0
    <[02-11-18 03:29:52.502] <MFB> ********************************
    ] <MFB> ***** Basic FLASH tests OK *****
    <[02-11-18 03:29:52.512] <MFB> ********************************
    <[02-11-18 03:29:52.522] <MFB> ---> Sector size 0 bytes L-Page size 4096 bytes <---
    S[02-11-18 03:29:52.532] Security: Disabled  
    H[02-11-18 03:29:52.532] H/w Decode enabled
    <[02-11-18 03:29:52.532] <MFB>  
     
     
    *[02-11-18 03:29:52.532] *** MFB 582 Jul  3 2014 04:05:49 B:FW_PPRO_5_6_1_20140326_836378:FW_PPRO_5_8_2_Release-906190
    *[02-11-18 03:29:52.552] *** Build Options : cfg/cfg_MLC_MIC_128Gb_MT29F512G08CKCAB_1Q_2C_2D -noenterprise -asic -subdir SF-2281_Board -pdump -elog -ecli -release -ecliLevel0 -div2 -sysclk300 -nochipsocket -mfb -noecli -suffix PP_R02238_s512 ANYHOST
    *[02-11-18 03:29:52.582] *** Chip RevId from HW: B03 (ID=625280), FW Targeted For: B02 ASI ***
    *[02-11-18 03:29:52.602] *** SysClk : 300 MHz
    *[02-11-18 03:29:52.602] *** Packer : 500 MHz
    *[02-11-18 03:29:52.602] *** Flash  : 830 MHz
    *[02-11-18 03:29:52.612] *** FlaDiv : 2
    *[02-11-18 03:29:52.612] *** GP1011 : 2 (0=Async ONFI, 1=Toggle, 2=ONFI, 3=Async Toggle)
    <[02-11-18 03:29:52.622] <MFB>  
    *[02-11-18 03:29:52.622] *** GPIO0 : 1
    <[02-11-18 03:29:52.622] <MFB> Scap charge wait
    <[02-11-18 03:29:52.632] <MFB> Scap charge done
    <[02-11-18 03:29:52.632] <MFB User> libSfStartC enter cfg:3fff4d38
    <[02-11-18 03:29:52.642] <MFB> RootFileOpen(): not allowed yet [fid:8, mode:00000001, flags:00000003].
    <[02-11-18 03:29:52.652] <MFB User> UserMain: CheckRetiredBlkCntAtClearSmart failed.
    <MFB> PIO Flash Rblock Test on 0 - bus:1 ce:2 die:2 lane:4 pagent:1 correctPwr:304 seed:dead6a4a markers:4000
     Errors in BUS:0 CE: 0 DIE:0 [  LANE 0: 0002,  LANE 1: 0003, <MB> ]
     Errors in BUS:0 CE: 1 DIE:0 [  LANE 1: 0002, <MFB> ]
     Errors in BUS:0 CE: 0 DIE:1 [  LANE 0: 0003,  LANE 2: 0043, <MB> ]
    <MFB> Special Bad Block Scan: Valid 0 NumBytes 959 numOnes 1
    <[02-11-18 03:30:03.991] <FB> Read Device ID: 2C A4 E5 3C A5 00
    <[02-11-18 03:30:04.001] <MFB> == Format mode ONE align 0 ==
    <[02-11-18 03:30:04.011] <MFB> ---> Sector size 0 bytes L-Page size 4096 bytes <---
    <[02-11-18 03:30:04.021] <MFB> Flash ID Check
    <[02-11-18 03:30:04.021] <MFB> Creating New Root
    <[02-11-18 03:30:04.021] <MFB> Bad Block Discovery ...
    <MFB> Number of Bad Blocks for SE/plane/lane
    <[02-11-18 03:30:04.437] <MFB>  SE pl: ln0ln1 ln2 ln3
    <[02-11-18 03:30:04.447] <MFB>   0  0:   1   1   1   1  
    <[02-11-18 03:30:04.447] <MFB>   0  1:   1   1   1   1  
    <[02-11-18 03:30:04.457] <MFB>   2  0:   1   1   1   1  
    <[02-11-18 03:30:04.457] <MFB>   2  1:   1   1   1   1  
    <[02-11-18 03:30:04.467] <MFB>   4  0:   2   1   1   1  
    <[02-11-18 03:30:04.467] <MFB>   4  1:   1   6   1   1  
    <[02-11-18 03:30:04.477] <MFB>   6  0:   1   1   1   1  
    <[02-11-18 03:30:04.477] <MFB>   6  1:   1   1   1   1  
    <[02-11-18 03:30:04.487] <MFB> Total Bad Block number is: 38 out of 32768
    <[02-11-18 03:30:04.487] <MFB> Added donor[0]= 45
    <[02-11-18 03:30:04.497] <MFB> Added donor[1]= 396
    <[02-11-18 03:30:04.497] <MFB> Added donor[2]= 400
    <[02-11-18 03:30:04.507] <MFB> Added donor[3]= 428
    <[02-11-18 03:30:04.507] <MFB> Added donor[4]= 486
    <[02-11-18 03:30:04.517] <MFB> Added donor[5]= 786
    <[02-11-18 03:30:04.517] <MFB> Enabling Remap Unit...
    <[02-11-18 03:30:04.517] <MFB> Erasing All Virgin Blocks...
    <MFB> No Host GDL!
    <[02-11-18 03:30:09.816] <MFB> Creating the Root Record ...
    816]<MFB> Input PE:     0
    <[02-11-18 03:30:09.869] <MFB> Drive RDD:100000 RDD Low:100000, PE:  3000 Options:0000 Warranty: 0
    <MFB> Format: WP Circuit Not Present (dynamic)
    <[02-11-18 03:30:11.369] <MFB> CeateAndVerifyRoot: fid=2 ibidx=6 buf=3fff0f9c buflen=3876
    <[02-11-18 03:30:11.379] <MFB> CreateAndVerifyRoot: fid=2 ibidx=7 buf=3fff0f9c buflen=3876
    <[02-11-18 03:30:11.389] <MFB> CreateAndVerifyRoot: fid=1 ibidx=2 buf=3fff0f84 buflen=24
    <[02-11-18 03:30:11.399] <MFB> CreateAndVerifyRoot: fid=1 ibidx=3 buf=3fff0f84 buflen=24
    f0f84 buflen=24
    <[02-11-18 03:30:11.429] <MFB> CreateAndVerifyRoot: fid=1 ibidx=5 buf=3fff0f84 buflen=24
    <[02-11-18 03:30:11.439] <MFB> CreateAndVerifyRoot: fid=0 ibidx=0 buf=3fff201c buflen=876
    <[02-11-18 03:30:11.449] <MFB> CreateAndVerifyRoot: fid=0 ibidx=1 buf=3fff201c bufln=3876
    <[02-11-18 03:30:11.459] <MFB> Initialize the Root ...
    <[02-11-18 03:30:11.459] <MFB> PPRO-15147 (LION-1540): Retired Root IBlocks=0.
     
     
    F[02-11-18 03:30:11.469] Found a valid Config Record.
     
     
     of Die / CE    = 2
            CE CFG (Bus Mode)     = 1-DIMM
            Number o Bus         = 1
            Flash Page Size       = 16384
            Flash Page /Block    = 512
            Number of Block / Die = 2048
            E-Page Size           = 512
            ECC Bytes             = 32
            ECC Correction Power  = 19
     
     
    <[02-11-18 03:30:11.529] <MFB> Low PE Flashware File Feature : NO
    <[02-11-18 03:30:11.529] <MFB> Coalesce Compression Feature  : YES
    <[02-11-18 03:30:11.539] <MFB> Single Plane Remap Feature    : YES
    <[02-11-18 03:30:11.549] <MFB> RootInit: WP Circuit Not Present (dynamic)
    <[02-11-18 03:30:11.549] <MFB> EVT LOG. Panic Dump slot 0 epa 0x00100002
    <[02-11-18 03:30:11.559] <MFB> EVT LOG. Panic Dump slot 1 epa 0x00100102
    <[02-11-18 03:30:11.569] <MFB> EVT LOG. Panic Dump slot 2 epa 0x00100202
    <[02-11-18 03:30:11.579] <MFB> EVT LOG. Panic Dump slot 3 epa 0x00100302
    <[02-11-18 03:30:11.579] <MFB> ------> Root Record Versions: CONFIG=1, PRR=1 (ib=3,pp=1),SRR=1 (ib=7,pp=1) <------
    <[02-11-18 03:30:11.599] <MFB> UE: epa=00180000 laneMask=0xF ufId=97 ffBytes=9248 numEpages=17
    <[02-11-18 03:30:11.609] <MFB> Saving Bad Block List ..
    <[02-11-18 03:30:11.619] <MFB> UE: epa=00180100 laneMask=0xF bufId=98 ffBytes=9248 nmEpages=17
    <[02-11-18 03:30:11.629] <MFB> UE: epa=00180200 laneMask=0xF bufId=99 ffByte=9248 numEpages=17
    <[02-11-18 03:30:11.639] <MFB> Saving Grown Defect List ...
    <[02-11-18 03:30:11.639] <MFB> UE: epa=00180300 laneMask=0xF bufId=100 ffBytes=9248 numEpages=17
    <[02-11-18 03:30:11.659] <MFB> Initializing SMART root file ...
    <[02-11-18 03:30:11.659] <MFB> UE: epa=00200000 laneMask=0xF bufId=101 ffBytes=9248 numEpages=17
    <[02-11-18 03:30:11.669] <MFB> UE: epa=00200100 laneMask=0xF bufId=102 ffBytes=9248 numEpages=17
    <[02-11-18 03:30:11.679] <MFB InitSmartLogRootFile is done
    <[02-11-18 03:30:11.689] <MFB> Initializing XTS Global Keys ...
    <[02-11-18 03:30:11.699] <MFB> UE: epa=00200200 laneMask=0xF bufId=103 ffBytes=9248 numEpages=17
    <[02-11-18 03:30:11.709] <MFB> Initializing Life Table ...
    <[02-11-18 03:30:11.709] <MFB> Saving Life Table ...
    <[02-11-18 03:30:11.719] <MFB> UE: epa=00200300 laneMask=0xF bufId=104 ffBytes=9248 numEpages=17
    <[02-11-18 03:30:11.729] <MFB> Set LBA Offset to 0 ...
    <[02-11-18 03:30:11.729] <MFB> Clearing the Map Table ...
    <[02-11-18 03:30:11.739] <MFB> Clearing the SIN Table ...
    <[02-11-18 03:30:11.739] <MFB> Saving the MAP Table1 ...
    <[02-11-18 03:30:11.749] <MFB> UE: epa=00280000 laneMask=0xF bufId=105 ffBytes=9248 numEpages=17
    <[02-11-18 03:30:11.759] <MFB> Saving the MAP Table2 ...
    <[02-11-18 03:30:11.769] <MFB> UE: epa=00280100 laneMask=0xF bufId=106 ffBytes=9248 numEpages=17
    11.779] <MFB> Saving the SIN Table ...
    <[02-11-18 03:30:11.789] <MFB> UE: epa=00280200 laneMask0xF bufId=107 ffBytes=9248 numEpages=17
    <MFB> Saving the Remap Table ...
    <[02-11-18 03:30:11.809] <MFB> UE: epa=00280300 laneMak=0xF bufId=108 ffBytes=9248 numEpages=17
    <MFB> UE: epa=00300000 laneMask=0xF bufId=109 ffBytes=9248 numEages=17
    <MFB> UE: epa=00300100 laneMask=0xF bufId=110 ffBytes=9248 numEages=17
    <MFB> Saving the RD Table ...
    <[02-11-18 03:30:11.879] <MFB> UE: epa=00300200 laneMask=xF bufId=138 ffBytes=9248 numEpages=17
    <MFB> Saving the ID Data ...
    <[02-11-18 03:30:11.899] <MFB> UE: epa=00300300 laneMask=0F bufId=139 ffBytes=9248 numEpages=17
    <[02-11-18 03:30:11.909] <MFB> Saving the Free Tale ...
    <[02-11-18 03:30:11.919] <MFB> UE: epa=00380000 laneMask=0xF bufId=141 ffBytes=948 numEpages=17
    <[02-11-18 03:30:11.929] <MFB> Finalizing the ROOT ...
    <[02-11-18 03:30:11.929] <MFB> UE: epa=00380100 laneMask=0xF bufId=142 ffBytes=9248 numEpages=17
    <[02-11-18 03:30:11.939] <MFB> Factory Setup finished; you may reboot or download Flashware now
    <[02-11-18 03:30:11.959] <MFB> UE: epa=00380200 laneMask=0xF bufId=143 ffBytes=9248 nuEpages=17
    <MFB> UE: epa=00380300 laneMask=0xF bufId=153 ffBytes=9248 numEages=17
    <[02-11-18 03:30:17.131] <MFB User> SCT_CONFIG_DRIVE_UNIQUE: user space synced
    3:30:17.131]<MFB> Firmware Fuse=0xFC88FC88, computed value=0xFC88
    <[02-11-18 03:30:20.231] <MFB> PPO_STAMP FROM IMAGE: 06 14 00 fd 00 00 00 00
    <[02-11-18 03:30:20.241] <MFB> STAMP OK at ffset 0x000000
    <[02-11-18 03:30:20.251] <MFB> RSA OK
    <[02-11-18 03:30:20.251] <MFB> UE: epa=00400000 laneMask=0xF bufId=157 ffBytes=9248 numEpages=17
    <MFB> <<<Read-Only Root Files Padding>>> Padding fid=3 iba=64 ppln=9 to 511
    <MFB> Need 536256 More!
    <[02-11-18 03:30:20.808] <MFB> SATA_UPDATE_IN_PROGRESS
    808]<MFB> UE: epa=00400100 laneMask=0xF bufId=159 ffBytes=9248 numEages=17
    <MFB> <<<Read-Only Root Files Padding>>> Padding fid=5 iba=66 ppln=9 to 511
    <MFB> UE: epa=00400200 laneMask=0xF bufId=160 ffBytes=9248 numEpages=17
    <MFB> Need 470720 More!
    <[02-11-18 03:30:21.445] <MFB> SATA_UPDATE_IN_PROGRESS
    445]<MFB> UE: epa=00400300 laneMask=0xF bufId=179 ffBytes=9248 numEages=17
    <MFB> <<<Read-Only Root Files Padding>>> Padding fid=3 iba=70 ppln=10 to 511
    <MFB> UE: epa=00480000 laneMask=0xF bufId=180 ffBytes=9248 numEages=17
    <MFB> <<<Read-Only Root Files Padding>>> Padding fid=5 iba=72 ppln=26 to 511
    <MFB> Need 405184 More!
    <[02-11-18 03:30:22.583] <MFB> SATA_UPDATE_IN_PROGRESS
    583]<MFB> UE: epa=00480100 laneMask=0xF bufId=208 ffBytes=9248 numEages=17
    <MFB> UE: epa=00480200 laneMask=0xF bufId=209 ffBytes=9248 numEages=17
    <MFB> <<<Read-Only Root Files Padding>>> Padding fid=3 iba=76 ppln=34 to 511
    <MFB> Need 339648 More!
    <[02-11-18 03:30:23.219] <MFB> SATA_UPDATE_IN_PROGRESS
    219]<MFB> UE: epa=00480300 laneMask=0xF bufId=245 ffBytes=9248 numEages=17
    <MFB> <<<Read-Only Root Files Padding>>> Padding fid=5 iba=78 ppln=10 to 511
    <MFB> UE: epa=00180200 laneMask=0xF bufId=246 ffBytes=9248 numEages=17
    <MFB> Need 274112 More!
    <[02-11-18 03:30:23.892] <MFB> SATA_UPDATE_IN_PROGRESS
    892]<MFB> UE: epa=00280300 laneMask=0xF bufId=35 ffBytes=9248 numEpages=17
    <MFB> <<<Read-Only Root Files Padding>>> Padding fid=3 iba=46 pgpln=9 to 511
    ]<MFB> UE: epa=00300300 laneMask=0xF bufId=36 ffBytes=9248 numEpages=17
    <MFB> <<<Read-Only Root Files Padding>>> Padding fid=5 iba=54 ppln=51 to 511
    <MFB> Need 208576 More!
    <[02-11-18 03:30:25.032] <MFB> SATA_UPDATE_IN_POGRESS
    <MFB> UE: epa=00400000 laneMask=0xF bufId=89 ffBytes=9248 numEpges=17
    <MFB> UE: epa=00400100 laneMask=0xF bufId=90 ffBytes=9248 numEpges=17
    <MFB> <<<Read-Oly Root Files Padding>>> Padding fid=3 iba=66 pgpln=60 to 511
    <MFB> Need 143040 More!
    <[02-11-18 03:30:25.667] <MFB> SATA_UPDATE_IN_PROGRESS
    667]<MFB> UE: epa=00400200 laneMask=0xF bufId=152 ffBytes=9248 numEpages=17
    <MFB> <<<Read-Only Root Files Padding>>> Padding fid=5 iba=68 ppln=9 to 511
    <MFB> UE: epa=00400300 laneMask=0xF bufId=153 ffBytes=9248 numEpages=17
    MFB> Need 77504 More!
    <[02-11-18 03:30:26.374] <MFB> SATA_UPDATE_IN_PROGRESS
    4]<MFB> UE: epa=00480000 laneMask=0xF bufId=223 ffBytes=9248 numEages=17
    <MFB> <<<Read-Only Root Files Padding>>> Padding fid=3 iba=72 pgpln=10 to 511
    6]<MFB> UE: epa=00480100 laneMask=0xF bufId=224 ffBytes=9248 numEages=17
    <MFB> <<<Read-Only Root Files Padding>>> Padding fid=5 iba=74 ppln=77 to 511
    <MFB> Need 11968 More!
    <[02-11-18 03:30:27.517] <MFB> SATA_UPDATE_IN_PROGRESS
    17]<MFB> UE: epa=00480200 laneMask=0xF bufId=47 ffBytes=9248 numEpages=17
    <MFB> Validate SHA on Input Stream Microcode: PASS!
    <[02-11-18 03:30:27.582] <MFB> Did ot find appendix signature.
    <[02-11-18 03:30:27.592] <MFB> Info 1: not a valid appendix
    <[02-11-18 03:30:27.602] <MFB> UE: epa=00480300 laneMask=0xF bufId=48 ffBytes=9248 numpages=17
    <MFB> <<<Read-Only Root Files Padding>>> Padding fid=3 iba=78 ppln=78 to 511
    <MFB> Validate SHA on Root File 3: PASS!
    <[02-11-18 03:30:28.339] <MFB> UE: epa=0018020 laneMask=0xF bufId=205 ffBytes=9248 numEpages=17
    <[02-11-18 03:30:28.349] <MFB> ILL Du SRC=4(IBIDX ff,IBA 634ba) to DST=5 (IBIDX a,IBA 1c)!!!
    <[02-11-18 03:30:28.359] <MFB> <<Read-Only Root Files Padding>>> Padding fid=5 iba=28 pgpln=0 o 511
    <MFB> UE: epa=00280300 laneMask=0xF bufId=206 ffBytes=9248 numEages=17
    <[02-11-18 03:30:28.863] <MFB> ILL Dup SRC=3(IBIDX 23,IBA 4e) to DST=4 (IBIDX 1,IBA 2e)!!!
    <MFB> <<<Read-Only Root Files Padding>>> Padding fid=4 iba=46 ppln=78 to 511
    <MFB> UE: epa=00300300 laneMask=0xF bufId=29 ffBytes=9248 numEpges=17
    <[02-11-18 03:30:29.385] <MFB> ILL Dup SRC=3(IBIDX 23,IBA 4e) to DST=6 (IBIDX 17IBA 36)!!!
    <MFB> <<<Read-Only Root Files Padding>>> Padding fid=6 iba=54 ppln=78 to 511
    <MFB> Validate SHA on Root File 4: PASS!
    <[02-11-18 03:30:30.132] <MFB> Download Microcde PASS!
    <[02-11-18 03:30:30.142] <MFB> SATA_UPDATE_COMPLETE
    <[02-11-18 03:30:30.142] <MFB> Warm Start (state=14) - Resetting ALL hardware blocks!
     
     
     
     
     
     
    sync code 0x00000000 --> 0x0710898E
    [02-11-18 03:30:30.238] Cannot find section with addr range: 0x80017EE0-0x80017FDF
    [02-11-18 03:30:30.238] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x8000B650-0x8000B74F
    [02-11-18 03:30:30.248] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x8000DCCC-0x8000DDCB
    [02-11-18 03:30:30.258] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x80009CFC-0x80009DFB
    [02-11-18 03:30:30.278] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x8000DCCC-0x8000DDCB
    [02-11-18 03:30:30.288] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x800117AC-0x800118AB
    [02-11-18 03:30:30.288] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x8000DCCC-0x8000DDCB
    [02-11-18 03:30:30.298] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x8000BCD8-0x8000BDD7
    [02-11-18 03:30:30.308] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x80014B78-0x80014C77
    [02-11-18 03:30:30.318] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x80014C74-0x80014D73
    [02-11-18 03:30:30.318] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x80014BFC-0x80014CFB
    [02-11-18 03:30:30.328] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x80014C1C-0x80014D1B
    [02-11-18 03:30:30.328] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x80014C20-0x80014D1F
    [02-11-18 03:30:30.328] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x80006D70-0x80006E6F
    [02-11-18 03:30:30.338] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x8000DCCC-0x8000DDCB
    [02-11-18 03:30:30.348] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Cannot find section with addr range: 0x8000BD48-0x8000BE47
    [02-11-18 03:30:30.348] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    GOT Rvrs call: "RSTF"
    [02-11-18 03:30:30.358]sectSize = 98356  
    [02-11-18 03:30:31.326] /    9   4132-   18   8228\   27  12324|   36  16420/   45  20516-   54  24612\   63  28708|   72  32804/   81  36900-   90  40996\   99  45092|  108  49188/  117  53284-  126  57380\  135  61476|  144  65572/  153  69668-  162  73764\  171  77860|  180  81956/  189  86052-  198  90148\  207  94244|  216  98340-  218  98392  
    [02-11-18 03:30:42.165] eCLI_SerialInit:103 String section 0x028028A4 size 98356
    [02-11-18 03:30:42.165] (WARNING: Msg Might Be Garbled Until Strings Sect is reloaded!)
    Status OK Loaded 1 sections 98356 bytes 0 msec
    [02-11-18 03:30:42.165] (Msg Should Be No Longer Be Garbled)
    [02-11-18 03:30:42.165]
     
    Добавлено:
    <[02-11-18 03:30:17.131] <MFB User> SCT_CONFIG_DRIVE_UNIQUE: user space synced  
    3:30:17.131]<MFB> Firmware Fuse=0xFC88FC88, computed value=0xFC88  
     
     
    А не известно где в прошивке Firmware Fusе ? Может как то подправить ?

    Всего записей: 86 | Зарегистр. 11-11-2017 | Отправлено: 02:25 11-02-2018
    Smyg1



    Advanced Member
    Редактировать | Профиль | Сообщение | ICQ | Цитировать | Сообщить модератору

    Цитата:
    <[02-11-18 03:24:21.595] <MFB> Factory Setup finished; you may reboot or download Flashware now.
    ...
    <[02-11-18 03:24:26.798] <MFB User> SCT_CONFIG_DRIVE_UNIQUE: user space synced
    3:24:26.798]<MFB> Firmware Fuse=0xFC88FC88, computed value=0xFC88
    <[02-11-18 03:24:29.898] <MFB> Inompatible image config level (fc00) for device eFuse fc88
    <[02-11-18 03:24:29.908] <MFB> STAMP INCOMPATIBLE at offset 0x000000
    <[02-11-18 03:24:29.918] <MFB> Download aborted! Failed to verify VicSignature!
    <[02-11-18 03:24:29.928] <MFB> Download error, ignore remaining 61440.
    <[02-11-18 03:24:29.938] <MFB> Download Microcode FAIL! Error:2, Bail out.
    <[02-11-18 03:24:29.948] <MFB> Unknown SATA_UPDATE_STATUS  
    ...
    <[02-11-18 03:30:30.132] <MFB> Download Microcde PASS!  

     
    покажите заголовок лицензии, с которым распаковывали DFP...

    Всего записей: 1892 | Зарегистр. 03-10-2006 | Отправлено: 11:05 11-02-2018 | Исправлено: Smyg1, 11:10 11-02-2018
    Buriaver_II

    Newbie
    Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
    Люди. А что, других DST, кроме "fw_MP3_Patch2_3-4-6" для SF1xxx не появилось?

    Всего записей: 19 | Зарегистр. 17-09-2017 | Отправлено: 13:53 11-02-2018
    Открыть новую тему     Написать ответ в эту тему

    Страницы: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

    Компьютерный форум Ru.Board » Hardware » Магнитные носители информации » Ремонт SSD накопителей на контроллерах SandForce (часть 3)

    Имя:
    Пароль:
    Сообщение

    Для вставки имени, кликните на нем.

    Опции сообщенияДобавить свою подпись
    Подписаться на получение ответов по e-mail
    Добавить тему в личные закладки
    Разрешить смайлики?
    Запретить коды



    Реклама на форуме Ru.Board.

    Powered by Ikonboard "v2.1.7b" © 2000 Ikonboard.com
    Modified by Ru.Board
    © Ru.Board 2000-2018

    BitCoin: 1NGG1chHtUvrtEqjeerQCKDMUi6S6CG4iC

    Рейтинг.ru